Оценок - 4, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note: • After printing with the “–” tape margin setting, hold down and press once to feed the tape before pushing in the tape cutter lever to cut it, otherwise some of the printed characters may be cut off. • After printing with the # or ## tape margin setting, push in the tape cutter lever to cut off the label, and then use scissors to cut along the printed dots ( : ) and centre the text within the label. PRINTING After you have print the label. . To print the label, press . The message “ PRINT” is displayed while the label is being printed, and the label slot at the top end of the machine. . To feed out 25 mm of tape (for example, after printing using the “–” tape margin setting), hold down and press once. The message “ FEED” is displayed while the tape is fed out. . To cut off the label, push in the tape cutter in the top-right corner of the machine. Note: • In order to prevent damage to the tape, do not try to cut it while the messages “ PRINT” or “ FEED” are displayed. • After printing with the # or ## tape margin setting, push in the tape cutter lever to cut off the label, and then use scissors to cut along the dots ( : ) and center the text within the label. REPEAT PRINTING This function allows you to print up to nine copies of the same label. Note: To quit the following procedure at any time without making any changes, press . 1 Press . 2 Press and until REPEAT is displayed, and then press (or ). The message “ 1-9? ” appears in the display. 3 Press and until the number of labels that you want to print appears on the right side of the display. OR Press the key (1-9) corresponding to the number of labels that you want to print. 4 Press (or or ) to print the labels. Note: • After printing with the “–” tape margin setting, hold down and press once to feed the tape before pushing in the tape cutter lever to cut it. • After printing with the # , ## or ### tape margin setting, push in the tape cutter lever to cut off the tape, and then use scissors to cut along the printed dots ( : ) and separate the labels. NUMBERING This function can be used to print many copies of the same text while increasing a selected number by 1 after each label is printed, for example, when printing labels containing a serial number (for example, 0123, 0124, and 0125). Note: To quit the following procedure at any time without making any changes, press . 1 Position the cursor below the number that you wish to increase. 2 Press . 3 Press and until NUMBER is displayed, and then press (or ). The message “ 1-9? ” appears in the display. 4 Press and until the last number that you want to print appears on the right side of the display. OR Press the key (1-9) corresponding to the last number that you want to print. Note: The last number that will be printed must be larger than the number selected in the text, otherwise the message “ ERROR” will appear when you try to print. 5 Press (or or ) to print the labels. Note: • After printing with the “–” tape margin setting, hold down and press once to feed the tape before pushing in the tape cutter lever to cut it. • After printing with the # , ## or ### tape margin setting, push in the tape cutter lever to cut off the tape, and then use scissors to cut along the printed dots ( : ) and separate the labels. MEMORY You can use the memory to store your most frequently used text. The text file remains in the memory, even after all characters are removed from the display by holding down and pressing . Later, the text can easily be reused by recalling it from the memory. The machine’s memory can store up to 300 characters, which can be divided into as many as nine text files. The maximum capacity for a single text file is 55 characters. STORING Note: To quit the following procedure time without making changes, press . 1 Press . 2 Press and until MEMORY is displayed, and then press (or ). 3 Press and until STORE is displayed, and then press (or ). The message “ 1-9? ” appears in the display. 4 Press and until the file number where you want to store the text is displayed. OR Press the key (1-9) corresponding to the file number where want to store the text. 5 Press (or ) to store the text. The text previously shown in the display reappears. Note: • If the file number you selected already contains text, the message “ ERROR” appears. Press (or ), and then select a different file number. • If nine text files are already stored, the message “ ERROR” appears. Press (or ), and then delete one of the stored text files before trying to store the current text. • If 300 characters are already stored, the message “ FULL” appears. Press (or ), and then delete one of the stored text files before trying to store the current text. RECALLING TEXT Note: To quit the following procedure at any time without making any changes, press . 1 Press . 2 Press and until MEMORY is displayed, and then press (or ). 3 Press and until RECALL is displayed, and then press (or ). The message “ 1-9? ” appears in the display. 4 Press and unt...