Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
• For best results, and longer printer life, use only TOSHIBA TEC recommended media. (Refer to the Supply Manual.) • Store the media in accordance with the specifications. • This printer mechanism contains high voltage components; therefore you should never remove any of the covers of the machine as you may receive an electrical shock. Additionally, the printer contains many delicate components that may be damaged if accessed by unauthorized personnel. • Clean the outside of the printer with a clean dry cloth or a clean cloth slightly dampened with a mild detergent solution. • Use caution when cleaning the thermal print head as it may become very hot while printing. Wait until it has had time to cool before cleaning. Use only the TOSHIBA TEC recommended print head cleaner to clean the print head. • Do not turn off the printer power or remove the power plug while the printer is printing or while the Indictor Lamp is flashing. E2- 1 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.2 Procedure before Operation 2.2 Procedure before Operation NOTE: 1. To communicate directly with a host computer, an RS-232C, Centronics, Ethernet, or USB cable is required. (1) RS-232C cable: 9 pins (do not use a null modem cable) (2) Centronics cable: 36 pins (3) Ethernet cable: 10/100 Base (4) USB cable: V2.0 (Full Speed) 2. Use of a Windows Driver will allow issuing media on the printer from a Windows application. The printer can also be controlled with its own programming commands. For details, please contact your TOSHIBA TEC representative. 2.3 Turning the Printer ON/OFF 2.3.1 Turning ON the Printer CAUTION! Use the power switch to turn the printer on/off. Plugging or unplugging the power cord to turn the printer on/off may cause fire, an electric shock, or damage to the printer. NOTE: If the Status Lamp is illuminated in red, go to Section 4.1, Troubleshooting Guide. This section describes the outline of the printer setup. 1. Unpack the accessories and printer from the box. 2. Refer to Safety Precautions in this manual and set up the printer at a proper location. 3. Make sure that the Power Switch is off. (Refer to Section 2.3.) 4. Connect the printer to a host computer with an RS-232C, Centronics interface, Ethernet cable or USB cable. (Refer to Section 2.4.) 5. Connect the Power Adapter to the printer, and then plug the Power Cord into a properly grounded power outlet. (Refer to Section 2.5) 6. Load the media. (Refer to Section 2.7.) 7. Adjust the position of the Feed Gap Sensor or Black Mark Sensor to match the media being used. (Refer to Section 2.7.) 8. Turn the Power ON. (Refer to Section 2.3.) 9. Install the Printer Drivers in the host computer. (Refer to the Printer Driver in the CD-ROM.) When the printer is connected to a host computer it is good practice to turn the printer ON before turning on the host computer and to turn OFF the host computer before turning off the printer. 1. To turn ON the printer power, press the power switch as shown in the picture below. Note that ( | ) is the power ON side of the switch. Power Switch 2. Check that the Indicator Lamp flashes slowly in orange for 5 seconds, then stays illuminated in green. E2- 2 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.3.2 Turning OFF the Printer CAUTION! 1. Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer. 2. Do not turn off the printer power while the Green Indicator Lamp is flashing as this may cause damage to the data being downloaded. 1. Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing. 2. To turn OFF the printer power press the power switch as shown in the diagram below. Note that ( .. ) is the power OFF side of the switch. Power Switch E2- 3 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.4 Connecting the Cables to the Printer 2.4 Connecting the Cables to the Printer CAUTION! Be sure to connect the serial or parallel cable while the printer and the host computer are power-off states. Failure to do this may cause electric shock, short-circuit, or breakdown of the printer. NOTE: For the specifications of the serial interface cable, refer to APPENDIX 2, INTERFACE. The following paragraphs outline how to connect the cables from the printer to your host computer, and will also show how to make cable connections to other devices. Depending on the application software you use to print labels, there are four possibilities for connecting the printer to your host computer. These are: • A serial cable connection between the printer’s RS-232C serial connector and one of your host computer’s COM ports. • A parallel cable connection between the printer’s standard parallel connector and your host computer’s parallel port (LPT). • An Ethernet cable connection between the printer’s Ethernet interface connector and one of your host computer’s Ethernet port. NOTE: . Use an Ethernet cable conforming...
Эта инструкция также подходит к моделям:Торговое оборудование - EO1-33088 (1.24 mb)