Оценок - 3, средний балл: 4.7 ( )

Производитель: Toshiba Размер: 964.41 kb Название файла: Язык инструкции:

Printer Carriage Release Lever 2. Label 3. Front Rubber Roller or Platen 4. Adjustable Label Edge Guides 6-2 7. SELF-PEELING FUNCTION EM1-33046A 7. SELF-PEELING FUNCTION 7. SELF-PEELING FUNCTION 1. Remove the printer’s front panel. CAUTION: When removing the front panel, care must be taken not to damage the label taken sensor harness. 2. Feed the backing of the label stock between the front rubber roller and the Self-peeling roller just in front of it, as shown in Fig. 7-1. 3. Feed the backing paper through the Backing Paper Opening in the front panel and replace the panel as shown in Fig. 7-2. 1 3 4 2 Fig. 7-1 Setting Up Printer for Self-Peeling Function 1. Printer Carriage Release Lever 3. Self-peeling Roller 2. Front Rubber Roller4. Backing Paper Fig. 7-2 Printer Ready for Self-Peeling Function 3 452 1 1. Printer Carriage Release Lever 4. Backing Paper 2. Printer Front Panel 5. Label 3. Backing Paper Opening 7-1 8. RIBBON LOADING INSTRUCTIONS EM1-33046A 8. RIBBON LOADING INSTRUCTIONS 8. RIBBON LOADING INSTRUCTIONS 1. Place an empty roll on the front ribbon rewind spindle. 2. Loosen the tape that secures the ribbon leader and fold it over the end of the leader. The tape will be used to affix the leader to the ribbon rewind roll. 3. Install the ribbon supply roll on the rear spindle so that the ribbon feeds from the top of the roll toward the rear. Position the ribbon roll at the center of the spindle. Guide the end of the leader through the ribbon feed slot. 4. Open the printer carriage by pulling up the release lever on the forward left side of the front rubber roller. Pull the leader forward and over the ribbon guide roller. 5. Using the tape at the end of the ribbon leader, affix the leader to the top of the rewind roll. Be careful to align the sides of the leader to the sides of the roll. 6. Wind the ribbon rewind roll until the ribbon leader has wound onto the roll and the black part of the ribbon is visible. Remove any excess slack. CAUTION: Center both ribbon supply and rewind rolls on the spindles and parallel these ribbon rolls with each other. Failure to do this may cause ribbon wrinkle or void printing. 7. Return the printer carriage to the down position CAUTION: Both sides of the printer carriage must be hooked completely, otherwise blurred print, media skew or ribbon wrinkle may be caused. 8. Close the top cover and press the Feed switch until the green On-line indicator light is illuminated. NOTE: Make sure that both sides of the top cover are completely hooked. 2 3 1 Fig. 8-1 Placement of Ribbon Supply Roll 1. Printer Carriage Release Lever 3. Ribbon Rewind Roll 2. Ribbon Supply Roll 4. Thermal Transfer Ribbon 8-1 8. RIBBON LOADING INSTRUCTIONS EM1-33046A 8. RIBBON LOADING INSTRUCTIONS Fig. 8-2 Proper Placement of Label Stock and Thermal Transfer Ribbon 8-2 9. INSTALL EXTERNAL LABEL ROLL MOUNT EM1-33046A 9. INSTALL EXTERNAL LABEL ROLL MOUNT 9. INSTALL EXTERNAL LABEL ROLL MOUNT 3 2 1 Fig. 9-1 Install External Label Roll Mount 1. External Label Roll Mount 2. Label Supply Roll Spindle 3. External Label Feed Opening 9-1 10. INSTALL MOMORY MODULE EM1-33046A 10. INSTALL MEMORY MODULE 10. INSTALL MEMORY MODULE WARNING! Turn the power OFF when inserting or removing the memory module. 1. Make sure the power is turned off. 2. Take off the cover from memory module . 3. Insert the memory module and press at the end of the slot. NOTE: Care must be taken not to insert the memory module in wrong orientation. 4. Put the cover on the memory module. 5. Turn on the power. 1 2 Fig. 10-1 Install Memory Module (Option) 1. Memory Module 2. Cover NOTES: 1. Be sure to protect a memory module by putting it in it's protective cover when not in use in the printer. 2. Do not subject the memory module to any shocks or excessive forces. 3. Do not expose the memory module to direct sunlight or store it close to a heater. 4. Do not expose the memory module to excessive humidity by wiping it with a wet cloth or storing it in a damp place. 5. Before inserting or removing the memory module, make sure that the power switch is turned off. 10-1 11. SELF TEST EM1-33046A 11. SELF TEST 11. SELF TEST To initiate the Self Test Mode, depress the Feed key while turning on the printer. The printer will first calibrate the label length. If a label edge is not detected within 7", the printer will then stop attempting to feed labels and treat the media as continuous thermal paper. Firstly, the printer will print a pattern to check the performance of the print head. Following the calibration of label length, the printer will print internal settings, including: 1. Print head checking pattern. 2. Printer type and firmware version 3. Head Run Distance 4. Serial port setting 5. Code page 6. Country code 7. Print Speed setting 8. Print Density setting 9. Label Size setting 10. Gap (Bline) Width and Offset Setting 11. Backing Paper Transparence 12. File list 13. Memory available After the self test is complete, reset the printer for use by turnin...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: