Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
an error will result on entering an excessive amount through the department key). |? Any time outside a sale Mode Lock : SET / GT Lock : Neutral 8 [@/FOR] I HALC I I LALC I I_ LC for the individual dept ( [SHIFT]) “►[DEPT] for the shifted depts. I HALC I I LALC I i_: Common LC for all depts [AT/TL] Repeatable for other departments ‘ HALC .... High Amount Listing Capacity (to be set in a 2-digit code.) ex.) I 3 I I 4 I .... indicate $39.99 ^-4 digits — equal to or smaller than $39.99 Value of the top digit LALC ..... Low Amount Listing Capacity (to be set in a 2-digit code.) ex.) I 2 I I 2 I 1 indicates $0.29 Î larger than $0.29 ■ 2 digits Value of the top digit ex.) To set the following LCs. Individual LCs (HALC $39.99, LALC $0.29) for Dept. 3. Common LCs (HALC $99.99, LALC $0.19). Mode Lock to SET, enter 8, depress [@/FOR], 3422 [DEPT 3] 9412 [AT/TL]. NOTES : 1. If the individual LC of a department is set, it prevails over the common listing capacity. 2. To reset a listing capacity, enter 00 before the [DEPT] key or the [AT/TL] key in the above operation. TEC STORE 1343 PEACH DRIVE PHONES 87-6437 Than« you Call again 11-20-90 «0 P08 03 HEAT 3422 9412 0034 10:59TM - 55 - E01 -110?<1 DEPARTMENT GROSS PROFIT RATE PROGRAMMING OR CHANGING (Submode No.13) (.QOKfomOfO Any lime outside a sale (oP^RATIOnT) Mode Lock : SET GT Lock : Neutral 13 [@/FORJ I Gross Profit Rate I 0 to 99.99 (%) -► {[SHIFT])-► [DEPT]- for the shifted departments. -> [AT/TL] Repeat for other departments NOTES : 1. The fraction resulted from the rate calculation will be discarded. 2. To cancel the gross profit once set, enter zero as department gross profit rate. ex.) To set following Gross Profit Rate Depl 1 10% Dept 3 20% Mode Lock to SET, enter 13, depress [@/FOR] Enter 10, depress [DEPT 1] Enter 20, depress [DEPT 3] [AT/TL] to end this program. - 56 - EOT -1102'I CUSTOMER FILE CODE (CHECK TRACK NO.) OPENING OR CLOSING (Submode No. 15) This program is available only when the “Check Track" option is selected. Programming is allowed any time outside a sale. Mode Lock : SET / GT Lock : Neutral ■ Opening : ► [AT/TL] Repeatable for different codes to be opened NOTES : 1. The Customer Fite codes that have been opened in this program will be accessed by entering the code and depressing the [PICK UP BAL] key for sale entry in a charge posting operation in the “REG” or "MGR" mode. At this time, the balance of the new customer assigned with the code wilt show zero which will be printed as the previous balance line item. On finalizing the saler the new balance will be printed at the bottom of the receipt, which will be stored in the same Customer File Code memory area. Thus the operator always uses (he [PICK UP BAL] key for both starting a new customer's account and recalling the customer's balance. 2. If all the opened Customer File codes are used up and a new customer file code is required to be opened during the business hours, the [CODE OPEN] key may be used. When a new code is entered, followed by [CODE OPEN], the code is printed as the previous balance line item with the balance zero on the receipt, and at the same time, the code is added to the fist of the Customer File Codes opened in the above “SET” mode operation. However, the use of the [CODE OPEN] key can be programmed to require Manager intervention, which can control (he operator’s opening of a new customer file code outside the list of Customer Fite Coc/es pre opened in the “SET” mode. 3. A maximum of 1000 Customer File Codes may be opened (max. WOO fixed). ex.) To open the folloeing customer file codes. Code to be opened Mode Lock to SET 1 15 [@/FOR] P 15 #000001 «000104 #000105 104 105 1 [#] 104 [#] 105 [#] [AT/TL] 0003 0036 USOOTH - 57 - EO 1 1 ! U24 Closing 15 [@/FORl -i—► [ITEM CORR] —► I Customer File Code I [#] -*-► [AT/TL] Repeatable for other codes to be closed. NOTE :lf the balance of the dosed is not zero, the Transfer memory of the code will automatically be adjusted to zero. In this case, the previous balance to be reset will be printed at the same time. ex.) To close the following Customer File Code that have once been opened: Code to be closed 104 Mode Lock to SET 15 [@/FOR] [ITEM CORR] 104 [#] [AT/TL] TEC STORE 1343 PEACH DRIVE PHONEs 87-6437 Thank xou Call again 11-20-90 #0 R 15 »000104 0.00 0002 0037 lliOOTH - 58 - KOI 1102-1 ) SALESPERSON CODE AND NAME PROGRAMMING AND DELETION (Submode No.20) By programming Salesperson Codes here, those codes may be used in sales entries. In addition, Ihe name of each salesperson can be programmed in maximum 8 characters. ■ Programming Any time outside a sale (for programming a new code and name, or for only changing the name) lip Mode Lock: SET / GT Lock: Neutral Repeatable for olher salespeople (max. 16 people) 20 [@/FOR] I Salesperson Code I [ST] 1 to 99 ■ Character Entries lor —► [ST[ Salesperson’s Name (max. 8 chara...