Оценок - , средний балл: ( )

Инструкция по эксплуатации Honeywell, модель 144860

Производитель: Honeywell
Размер: 1.34 mb
Название файла: 83d348f0-af1e-4d2d-b329-4d5feb74cdd8.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete operating instructions. 44002-01 r051807 IMPORTANT INFORMATION This thermostat is designed to work on the following heating and cooling systems: Up to 2 Stage Heat/2 Stage Cool Millivolt Systems Heat Only or Cool Only Systems 2-wire Hydronic Systems Single and Multi-Stage Heat Pumps AC or Hard-wired Gas, Electric or Oil Systems This thermostat is not designed for use with 110V/220 V systems. If you are unsure of what kind of heating and cooling system you have, please contact a qualified HVAC Technician for assistance. INSTALLATION PROCEDURES TOOLS This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver, Small Phillips-head screwdriver, Hammer Electric drill and 3/16” bit, Three 1.5 Volt (AA) size alkaline batteries 44002-01 r051807 NOTICE OF CAUTION! DO NOT disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper connection. YRCGWwYRCGW 44002-01 r051807 YRCGWYRCGW 44002-01 r051807 UNINSTALLING THE EXISTING UNIT 1. Turn the system power OFF at the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. (Failure to turn off the power to the existing thermostat before removal could damage your system.) 2. Remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged.) 3. Locate, but do not disconnect the wires. (If wires are not visible, they may be connected to the back of the wall plate. Some models may have doors that open to expose the wires and mounting screws.) 4. Do not let the wires slip back into the wall during disconnection. You may want to secure the wires to the wall as you disconnect them. After all wires are labeled, disconnect each wire and remove the existing wall plate. (Any unused wires should be capped with an approved electrical connector, such as electrical tape.) 44002-01 r051807 44002-01 r051807 5. Using the provided stickers, label each wire according to the chart. If the terminals are not labeled, contact a qualified HVAC technician. NOTE: Wire colors do not always comply with standards; therefore, wire color should be ignored. Refer to the existing terminal designation for proper identification. If wires marked “Y” or “C” are both present, “C” may be a Common wire and provides 24 VAC power to the unit. Connecting it greatly extends battery life. If there is no "C" wire, the thermostat will run on battery power. 44002-01 r051807 if your existing thermostat is marked: label the wire with this sticker: RHRHRHHeating Transformer Power SupplyY1 / Y2Cooling Stage 1 or 2W1 / W2Heating Stage 1 or 2CCC24 VAC Common(if available) CONVENTIONAL HVAC SYSTEMSGGGFanR / RCR/RCR/RCCooling Transformer Power Supplyif your existing thermostat is marked: label the wire with this sticker: W1 W2W2 W1Y1 Y2Y2 Y1 See pages 72-73 for a complete wiring diagram. 44002-01 r051807 if your existing thermostat is marked: label the wire with this sticker: R / RCR/RCR/RC24 VAC Power SupplyY1 / Y2Compressor Stage 1 or 2W2W2W2Auxilliary HeatEEEEmergency HeatCCC24 VAC CommonHEAT PUMP SYSTEMSOOOCool Mode Powered Reverse ValveBBBHeat Mode Powered Reverse ValveGGGFanLLLSystem Monitorif your existing thermostat is marked: label the wire with this sticker: Y1 Y2Y2 Y1Y1 Y2 See pages 74 for a complete wiring diagram. 44002-01 r051807 Y1Y2W3RH RCRGW2BW1OECW G Y RC L 44002-01 r051807 MOUNTING THE WALL PLATE 1. Remove the wall plate from the Hunter thermostat by gently pulling the wall plate from the back of the thermostat. 2. Position the new wall plate on the wall horizontally and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter thermostat wall plate or, if there are no existing holes, visually level the wall plate and mark the wall for two holes. 44002-01 r051807 W G Y RC 44002-01 r051807 4. Remove the wall plate from the wall and drill two 3/16” holes where marked. 5. Tap the plastic anchors into the holes until they are flush with the wall. 6. Reposition the wall plate on the wall, pulling the wires through the wall plate opening. Insert the mounting screws through the wall plate and into ...