Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Off Hp 3 OFF Setup Press MODE Continued Page 12 Advanced Setup Advanced Setup B Select the reversing valve polarity for Heat Pump, O or B. (Step 4 only appears if heat pump is on in step 3) O 0 4Setup Press Eh 5 OFF Setup MODE Select Electric Heat On or Off. (Step 5 only appears if heat pump is off in step 3) Press 2 6Setup 88 MODE Adjust the deadband from 1 - 6 degrees. Press 2 7 COOL HEAT Setup MODE Adjust the minimum difference between cooling & heating setpoints. (0 - 6 ) Press MODE Continued Page 13 Advanced Setup Advanced Setup Select the cycles per hour limit. d=cycles per hour limit defeated. d1=d + defeat 5 min. Compressor lockout. (d, d1, 2 - 6) 6 8 Cy Setup Press MODE On Select the display backlight always On, or Off after 8 seconds. Off L I 9 ON Press MODE C Select thermostat operation in degrees Fahrenheit or Centigrade. Setup F I0 F MODE FAN Press the Mode button. While holding the Mode, press the Fanbutton for 2 seconds to leave the Setupscreens. If no buttons are pressed, thedisplay will leave the setup screens after30 seconds. Page 14 Advanced Setup Advanced Setup Advanced Setup Table Step # Description Range Factory Default 1 Time of day clock set 24 hour 12:00 Am 2 Day of the week Sun -Sat Monday 3 Heat Pump Off / On Off 4 Reversing Valve polarity O / B O 5 Electric Heat Off / On Off 6 Deadband or Temperature swing 1 -6 2 7 Forced minimum difference heat/cool 0 -6 2 8 Cycles per hour d, d1, 2 -6 6 9 Thermoglow backlight Off / On On 10 Fahrenheit or Centigrade F / C F Page 15 About Advanced Features & Operation About Advanced Features & Operation 2 STAGE OPERATION - The 2nd Stage of heat or cool is turned on when (1) the 1st Stage has been on for a minimum of two minutes, and (2) the temperature spread from the setpoint is equal to or greater than: the setpoint plus the deadband, plus 2 degrees. Heating Cooling 2 degrees Dead Band Dead Band 2 degrees Heat Setpoint Cool Setpoint 1st Stage turn on 2nd Stage turn on 1st Stage turn on 2nd Stage turn on MINIMUM HEAT/COOL SETPOINT DIFFERENCE - The Heat and Cool setpoints will not be allowed to come any closer to each other than the value set in Advanced Setup step # 7, on page 13. This minimum difference is enforced during Auto changeover and Program On operation. Page 16 About Advanced Features & Operation About Advanced Features & Operation EMERGENCY HEAT - Is a feature available to Heat Pump installations. To turn on Emergency Heat press in the Fan button. While holding the Fan button press the Up button for 2 seconds. The Cool setpoint display will read ‘EH’. 73 eh I2:00 74 Su Press for Emergency Heat Fan During Emergency Heat the thermostat will turn on the fan and the 2nd stage of heat, when there is a demand for heat, locking out the 1st stage compressor. Exiting Emergency Heat is the same as entering. During Emergency Heat only OFF and HEAT are available. ELECTRIC HEAT - Selecting Electric Heat on, page 13, step 5, will cause the thermostat to turn on the fan immediately any time there is a heat demand. Since all gas furnaces control the fan, this feature should be off unless the heater is only electric. Page 17 About Advanced Features & Operation About Advanced Features & Operation KEYPAD LOCK -To prevent unauthorized use of the thermostat, the front panel buttons may be disabled. To disable, or ‘lock’ the keypad, press and hold in the Mode button. While holding the Mode button in, press the Up and Down buttons in together. The Locked icon will appear on the display. Press all 3 for Keypad Lockout MODE To unlock the buttons, again press and hold the Mode button. While holding the Mode button in, press the Up and Down buttons in together. The Locked icon will disappear from the display. Page 18 Locked70 85 55 ProgramOn Am COOL HEAT SuI2:00 Su Night About Advanced Features & Operation About Advanced Features & Operation DUAL SETPOINT BEHAVIOR - The adjustable setpoint range is: 35 - 99 degrees in Fahrenheit and 7 - 35 degrees in Centigrade. When in the modes Heat or Cool, this adjustable range is unhampered. When adjusting any Auto mode, including programming Occupied and Unoccupied periods, the 1050 will not allow the Heat setpoint to get closer to the Cool setpoint than the value programmed as the minimum difference in step 7, page 13. When entering the Auto mode from Cool, the Heat and Cool setpoints will remain spread apart by the amount that they were adjusted, prior to entering Auto. For example: If the Cool setpoint was set to 80 while in the Cool mode and the Heat setpoint was adjusted to 70 while in the Heat mode, upon entering the Auto mode the Heat and Cool setpoints would be 80 and 70. Both setpoints would then move up and down together, (in this example spread by 10 degrees), by pressing the up or down buttons. To move the Heat and Cool setpoints closer together, enter the Cool or Heat mode by pressing the Mode button, then adjust the setpoint(s) closer together. Heat is limited to how close it can come to Cool by step 7, pag...