Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
OWNER’SMANUALOWNER’S MANUAL OPTIONAL HUMIDITY MODULEOPTIONAL HUMIDITY MODULE Accepts theAccepts the COMMERCIALCOMMERCIAL THERMOSTATTHERMOSTAT P/NP/N 33CS4000133CS400 01 AUTO I2:00 Su Pm HEAT COOL 72 74HEAT COOL& CAUTION Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION NEVER PUT MORE THAN ONE JUMPER ON THE SAME MISC JUMPER BLOCK! THIS MAY DAMAGE YOUR THERMOSTAT. OK MISC3 MISC3 NOTE: Due to variations in environmental conditions, it is not always possible to achieve the desired humidification or dehumidification setpoint. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4Z95 Thermostat 33CS400-01 Tested to Comply with FCC Standards FOR HOME OR OFFICE USE FCc Page i Page 14.1 Section 14 Contents: Adjusting the Heat/Cool Differential..............................14.2 Adjusting the Cycles Per Hour..................................14.3 Adjusting the Deadband..........14.4 Adjusting the Minutes of Run-Time Before the Next Stage...............................14.6 Selecting 2nd Stage Turn Off Temperature.....................14.7 SECTION 14 TimersandDeadbandsTimers and Deadbands 14 HowtoUseThisManualHow to Use This Manual Header shows section # and title of section Section contents Section and page # Page 14.1 Section 14 Contents: Adjusting the Heat/Cool Differential..............................14.2 Adjusting the Cycles Per Hour..................................14.3 Adjusting the Deadband..........14.4 Adjusting the Minutes of Run-Time Before the Next Stage...............................14.6 Selecting 2nd Stage Turn Off Temperature.....................14.7 SECTION 14 TimersandDeadbandsTimers and Deadbands 14 HowtoUseThisManualHow to Use This Manual Header shows section # and title of section Section contents Section and page # The Table of Contents divides the thermostat features into sections making it easier to quickly find information. The first page of each section contains a more detailed list of the contents within that section, such as the example page shown below. Visible section tab on the side of the page In addition, this manual also has an Index to help you find any information regarding this thermostat quickly. Page ii GlossaryofTermsGlossary of Terms GlossaryofTermsGlossary of Terms Auto-Changeover: A mode in which the thermostat will turn on the heating or cooling based on room temperature demand. Configurable Output Jumper: Using jumpers on the thermostat you can configure the MISC1, MISC2, and MISC3 terminals to control humidification, dehumidification, and 2nd stage cooling. Cool Setpoint: The warmest temperature that the space should rise to before cooling is turned on (without regards to deadband). Deadband: The number of degrees the thermostat will wait, once setpoint has been reached, before energizing heating or cooling. Dehumidify: To reduce the amount of moisture in the air. Differential: The forced temperature difference between the heat setpoint and the cool setpoint. Heat Setpoint: The coolest temperature that the space should drop to before heating is turned on (without regards to deadband). Humidify: To increase the amount of moisture in the air. Icon: The word or symbol that appears on the thermostat display. Mode: The current operating condition of the thermostat (i.e. Off, Heat, Cool, Auto). Non-Programmable Thermostat: A thermostat that does not have the capability of running the Time Period Programming. Temperature Swing: Same as Deadband. Page iii T TT a aa b bb l ll e ee o oo f ff C CC o oo n nn t tt e ee n nn t tt s ss Quick Start Getting to Know YourThermostat Basic Operation Viewing Temperatureand Humidity Sensors Programming theFan OperationThermostat DisplayOptions Humidification Dehumidification Viewing EquipmentRun Times Electric Heat and Heat Pump Operation Timers and Deadbands Programming RemoteSensor OperationProgramming the DryContact Programming the RunTime Alerts Configuring the MISCOutputsFactory Defaults, Calibration, and Sensors Accessories Advanced Setup Table Override Operation Page iv SECTION 1 Q QQ u uu i ii c cc k kk S SS t tt a aa r rr t tt 1 Section 1 Contents: Selecting the Heat or Cool Mode............................................1.2 Selecting Your Desired Temperature................................1.3 Using the Fan Button...................1.3 Note: Following the instructions in this section will allow you to operate your thermostat using the factory default settings. These settings are depicted in the illustrations throughout this manual. Page 1.1 Selecting the Heat or Cool ModeSelecting the Heat or Cool Mode 1 1 Select Mode by Pressing the MODE Button Heating Only The HEAT setting indicates the temperature the roo...