Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
If no buttons are pressed for 5 sec, the display will change back to show room temperature. Timeguard Timer A 5- --minute timeguard is built into the thermostat immediately upon power up, and any time the compressor turns off. The compressor will not turn on until the timeguard has expired. The timeguard affects only compressor operation. Pressing UP and FAN buttons simultaneously will override the timeguard for 1 cycle. With PH or PC selected under Option 01, this timer is defeated. Cycle Timer In normal heating and cooling operation the thermostat will not allow more than 4 equipment cycles per hour (or 1 cycle every 15 minutes). Both the Y and W outputs have a 15- --minute timer that starts counting down when the output is turned on, (e.g., if Y output is turned on for 9 minutes and then satisfies, it cannot turn back on for another 6 minutes regardless of demand). However, pressing UP and FAN buttons simultaneously or changing the setpoint will override the timer for 1 cycle. Minimum on Timer Once the equipment has turned on, it will remain on for a minimum of 3 minutes regardless of demand. However, the equipment can turn off in less than 3 minutes if a change in setpoint or a change in mode occurs. Staging Timer If the thermostat is a heat pump model, it has 2- --stage heat capability. With HP operation, there is a 15- --minute delay between the first and second stages of heat. The Y output will energize first, then 15 minutes later, W is allowed to come on if the thermostat determines it is not satisfying the demand. However, if the heating demand is greater than 5_F, there will be only a 30 second delay before bringing on W. Auxiliary Heat Indicator A green LED indicates the use of auxiliary heat or emergency heat. Error Messages “--- --” (two dashes) will be displayed if the thermostat cannot properly read room temperature. If “- --- --” appears, replace thermostat. E4 will be displayed if the thermostat has an internal memory failure. If E4 appears, replace thermostat. Step 5 — Check Thermostat Operation Fan Operation 1. Press FAN button. This will start continuous fan operation. FAN annunciator will turn on. 2. Press FAN button again. This will stop continuous fan operation. FAN annunciator will turn off. Heating Operation 1. Press H/C button until HEAT is displayed. 2. Press UP button until LCD readout reads 3_F above room temperature. Press UP and FAN buttons simultaneously to defeat timers. Heating system should begin to operate immediately. 3. For HP thermostats only, press H/C button until EMHT (emergency heat) appears. Press UP and FAN buttons simultaneously to defeat timers. Emergency heating (W is ON, Y is OFF) should begin immediately. Cooling Operation 1. Press H/C button until COOL is displayed. 2. Press DOWN button until LCD readout reads 3_Fbelow room temperature. Press UP and FAN buttons simultaneously to defeat timers. Cooling system should begin to operate immediately. Table 1 shows the thermostat outputs for each available stage of heating or cooling. It may be useful in checkout or troubleshooting. TBNAC/ TBNHP Table1–OutputsEQUIPMENTCONFIGURATIONOPTION#1THERMOSTATFACTORYCONFIGURATIONCOOLSTAGE1HEATSTAGE1HEATSTAGE2EMHEATAC,PCAC,HPY,GW------------ HP,PHRVS=CHPY,G,O/BY,GY,G,WWHP,PHRVS=HHPY,GY,G,O/BY,G,W,O/BW 3 WIRING DIAGRAMS A06566 A06567 Fig. 1 - --A/C Thermostat Typical Installation Fig. 2 - --HP Thermostat Typical Installation TBNAC/ TBNHP Copyright 2007 Carrier Corp. S 7310 W. Morris St. S Indianapolis, IN 46231 Printed in U.S.A. Edition Date: 02/07 Catalog No: TB--NAC-- 1SI Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Replaces: NEW 4 TB---NACTB---NHPBaseSeriesNon---ProgrammableThermostatHomeowner’sGuideTB---NACTB---NHPBaseSeriesNon---ProgrammableThermostatHomeowner’sGuide A07108 BaseNon- ---ProgrammableThermostat 1. To Select the Mode: Use the H/C button to move between the choices. OFF, HEAT, COOL, or EMHT will appear on the display. EMHT will only appear on heat pump models. 2. To Select the Fan Operation: Use the FAN button to move between continuous fan (indicated by the FAN ON icon) and auto fan operation. 3. To Read the Room Temperature: The large display reads room temperature until a button is pressed. 4. To Adjust the Setpoint: In normal operation, the large display shows room temperature. At the first press of the UP or DOWN button, the large display shows the current setpoint and the SET TEMP icon is turned on. Further presses of the UP or DOWN button adjust the setpoint upward or downward. Five seconds after the last button press, the display returns to the room temperature and the SET TEMP icon turns off. Carrier Corporation FOR SERVICE OR REPAIR, FOLLOW THESE STEPS IN ORDER: FIRST: Contact the installer. You may find their name on the furnace or in your Homeowner’s Packet. If the installer’s name is not known, call your builder or home retailer if yours is a new residence. SECOND: Cont...
Эта инструкция также подходит к моделям:Термостаты - TB-NHP (390.28 kb)