Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
If heavy cleaning is required, the following procedures are recommended: CARE INSTRUCTIONS: Failure to follow these care instructions may damage the Faucet's finish. 3/4" CLASSIC THERMOSTAT TRIM KIT with SEPARATE VOLUME CONTROL C O L D HOT TEMP O F F ON TOP 1 Remove PLASTER GUARD (1). Remove HANDLE SCREW and ADAPTER (7) from rough valve. 1 Push CAPS (2 & 3) as shown onto CONTROL VALVES (4). TRIM INSTALLATION Push ESCUTCHEON (5) onto CAPS (2 & 3) and attach with (60mm) SCREWS (6) to valve. Push COVER PLATE (7) onto CAPS (2 & 3) and snap into holes in ESCUTCHEON (5) to secure. 4 3 2 7 5 7 6 1 3 1 4 5 7 7 6 6 8 9 2 2 INSTALL HANDLES TWO SPLINES KNOB MOUNT ARROW Figure 1 O F F ON O F F ON Install HANDLE ADAPTER (1) onto VOLUME CONTROL SPLINE (2). Align CROSS HANDLE (3) and push onto HANDLE ADAPTER (1). Install HANDLE SCREW (4) in CROSS HANDLE (3) and tighten with flat blade screwdriver. Insert index button (5). Align the two splines in LEVER HANDLE (6) with the knob mount arrow (Figure 1) and push LEVER HANDLE (6) onto KNOB MOUNT (7). Install HANDLE SCREW (8) in LEVER HANDLE (6) and tighten with phillips screwdriver. Insert index button (9). Should the hot and cold water supply pipes have been transposed making adjustment impossible, proceed as follows: TRANSPOSED SUPPLY PIPING 3 OR BACK TO BACK INSTALLATION Remove check stops and re-install them transposed. Shut off water supply. Remove handle and rim. (Reverse steps 1 and 2. CHECK STOP (RED TO BLUE) Turn the water supply back on and perform the temperature adjustment in step 2. Assemble HANDLES and TRIM. CHECK STOP (BLUE TO RED) Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left. M968419 REV 1.1 O F F NO 3 4 4 4 TEMPERATURE ADJUSTMENT SET HOT LIMIT STOP Check that arrow marking B points to the 3 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 3 o'clock position. See Figure 1. For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (4) until the spout temperature is 100 F. Check that arrow "A" on the KNOB MOUNT (4) still points 3 o'clock position after adjusting the thermostat to 100 F. If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (4) by pulling it towards you while standing directly in front of the valve. Reinstall the KNOB MOUNT (4) with arrow "A" 3 o'clock position. The maximum mixed water temperature is set at 109 F at the factory. This setting can be changed if desired. Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 112 F. Reinstall RED LOCKING DEVICE. See step 3 for LEVER HANDLE (3) installation. Pull out INDEX BUTTON (1) and remove LEVER HANDLE SCREW (2). Pull off LEVER HANDLE ASSEMBLY (3). ARROW "A" BLACK CLAMP ARROW "B" RED LOCKING DEVICE TEMPERATURE LIMIT STOP 2 1 ARROWS AT 3 O'CLOCK POSITION Figure 1 KNOB MOUNT 112 109 104 O F F NO M968419 REV 1.1 A908593-YYY0A VOLUME CONTROL HANDLE 918428-0070A VOLUME HANDLE SCREW A954049-YYY0A VOLUME HANDLE CAP A954043-YYY0A TEMPERATURE HANDLE CAP 918416-0070A TEMPERATURE M961112-YYY0A HANDLE SCREW TEMPERATURE CONTROL HANDLE 918434-YYY0A ESCUTCHEON SCREWS MODEL NUMBER CHROME POLISHED BRASS SATIN 002 099 295 Replace the "YYY" with appropriate finish code 3/4" CLASSIC THERMOSTAT TRIM KIT with SEPARATE VOLUME CONTROL T050.541 HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800 442-1902 Weekdays 8:00 a.m. to 8:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of American Standard Inc. © American Standard Inc. 2003 918049-0070A HANDLE ADAPTER M909625-YYY0A FRONT COVER PLATE M962365-YYY0A ESCUTCHEON M907093-YYY0A VOLUME CAP 907090-YYY0A TEMPERATURE CAP O F F ON C O L D HOT TEMP M968419 REV 1.1 CENTRAL THERMOSTAT WITH VOLUME CONTROL Installation Instructions M968255Rev.1.1 R520 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M ASSE 1016 ROUGHING-IN DIMENSIONS CONNECTIONS ARE: 1/2" NPT 5-7/8 II II 6-1/4 3-15/16 7 3-5/8 1-5/8 - 2-1/2 1/2" NPT TUB 1/2" NPT INLET 1/2" NPT INLET TOP 1/2" NPT SHOWER IMPORTANT: WHEN NOT USING A DIVERTER SPOUT A SEPARATE DIVERTER VALVE MUST BE USED. NOTE: MINIMUM FLOWING PRESSURE REQUIRED FOR THIS SYSTEM OPERATING WITH ONE SHOWER HEAD AND 2 BODY SPRAYS IS 40 PSI TUB PORT MUST BE PLUGGED HOT 1/2" 1/2" COLD TUB PORT MUST BE PLUGGED HOT 1/2" 1/2" COLD THERMOSTATIC BATH/ SHOWER INSTALLATION USING A TWIN ELL, DIVERTER SPOUT AND FIXED SHOWER THERMOSTATIC SHOWER INSTALLATION USING A DIVERTER VALVE, FIXED SHOWER HEAD AND ADJUSTABLE HAND HELD SHOWER THERMOSTATIC SHOWER INS...