Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
• For detailed information on the use of the VCR, refer to the operation manual of the VCR. REMOTE KEYPAD Use to enter two-digit code numbers when identifying your VCR. ENTER FF Press to rapidly advance the tape. For some VCRs, you may need to press STOP first, then FF. In Playback mode, hold button down to view the picture moving rapidly in forward direction. VCR CHANNEL UP ( ) / DOWN ( ) Press to scan up or down through channels on the VCR. RECORD Press to begin recording. PIP BUTTONS See pages 32 - 33. 36 32-48 27NS300/32/36NS400 1.1 36 5/31/00, 8:26 AM Operation of Remote Control (Continued) REMOTE KEYPAD VCR POWER DISPLAY CHANNEL UP (8)/ DOWN (9) TV-CATV L HOW TO IDENTIFY A VCR The remote control may already be set to operate your VCR. Try this initial check to see if going on to the following “identify” section is necessary. (1) Point remote towards VCR and press VCR POWER. (2) Does the remote turn the VCR ON and OFF? • If yes, the remote is ready to operate the VCR and no further steps are needed. • If no, continue to the “identify” section. L To Identify Your VCR – Direct Entry Method. Use the following steps and list to quickly find the remote control code for your accessory VCR. • First look up your VCR’s remote control code number before going through the direct code entry steps control. • If this procedure does not identify your accessory VCR, use the Search method of identification (described in the next section). (1) Slide TV-CATV switch to TV. (2) Press and hold down DISPLAY and CH DOWN (9)on your remote control. Then release both buttons. (3) Within ten seconds after releasing DISPLAY and CH DOWN (9), enter your VCR’s two- digit remote control code number using REMOTE KEYPAD (refer to list). • The remote control is now ready to send commands to your VCR. Some brands have more than one remote code listed due to changes in the remote codes from early to later model years, or due to format differences (VHS/BETA). In such cases, you may have to try more than one code to find the code your VCR accepts. NOTE: Depending on the model, year produced, brand, and type of VCR, some models may not be compatible with the remote control. L To Identify Your VCR – Search Method. (1) Slide TV-CATV switch on the remote to TV. (2) Press POWER on the VCR to ON. (3) Stand at least six feet away from the front of the VCR. Point the remote towards the VCR. Hold down DISPLAY and CH UP (8) at the same time. KEEP HOLDING THE BUTTONS DOWN. (4) Watch the Channel Number indicator on the VCR, Channel numbers will scan up when the VCR has been identified. Release DISPLAY and CH UP (8) as soon as the channel numbers start to scan up. The VCR’s remote control code number has been identified, and the remote is ready to operate the VCR. 37 32-48 27NS300/32/36NS400 1.1 37 5/31/00, 8:26 AM Operation of Remote Control (Continued) TV DISPLAY POWER REMOTE KEYPAD CHANNEL UP (8)/ DOWN (9) TV-CATV TIPS ON IDENTIFYING YOUR VCR: If your VCR model does not have the CHANNEL UP function on its remote control, it cannot be identified using the SEARCH method of identifying. For such models, please try the DIRECT ENTRY method of identifying. Be Patient: a minute or two can seem a lot longer when you’re waiting for something to happen, but the code should be identified within two minutes. Remember, it is only a one-time set-up. Be careful not to let the VCR scan more than five channels when the indicator starts to move up. If you continue holding down the DISPLAY and CH UP (8) after five channel scans, the proper remote code can be passed up, and the two minute identify cycle will have to be repeated. If a channel change does not occur on the VCR within two minutes, read the identifying instructions again and repeat the steps. Should a channel change still not occur the remote will not operate with the desired VCR. L HOW TO IDENTIFY A CABLE CONVERTER L To Identify Your Cable Converter – Direct Entry Method. Use the following steps and list to quickly find the remote control code for your cable TV converter. • First look up your converter’s remote code number before going through the direct code entry steps below. • If this procedure does not identify your converter, use the Search method of identification (described in the next section). 38 REMOTE CONTROL VCR BRAND CODE NUMBER Akai ________________ Audio Dynamics ______ Broksonic ___________ Canon ______________ Capehart ____________ Craig _______________ Curtis Mathis _________ Daewoo ____________ DBX _______________ Dynatech ___________ Emerson ____________ Fisher ______________ Funai _______________ GE ________________ Goldstar ____________ Hitachi ______________ Instant Replay ________ JC Penney __________ JVC ________________ Kenwood ____________ Lloyds ______________ Magnavox ___________ Magnin _____________ Marantz _____________ Memorex ____________ Minolta _____________ Mitsubishi ___________ Montgomery Ward ____ Multitech ____________ NEC _______________ Panasonic ___________ Pentax _...