Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
. PG – Parental Guidance Programming intended for a general audience, but which may not be suitable for younger children. Parents may consider some content not appropriate for children aged 8-13. . 14+ – 14 Years and OlderParents are strongly cautioned to exercise discretion in permitting viewing by pre-teens and early teens. Programming may contain mature themes and scenes of intense violence. . 18+ – Adult Material intended for mature audiences only. Directions to set Canadian V-Chip Ratings Press the MENU button .† To V-CHIP v® To operate (lock icon appears) Press ZERO to access V-Chip setup options .† To SET CANADIAN RATINGS ENG (for English) v® To enter ratings menu For example: To block viewing of programming rated 14+ and 18+: v® To the 18+ Column Press the OK button to lock v® To the 14+ Column Press the OK button to lock Press the MENU button to finish ...................................................................................................................... Note: • For instructions on “SET CANADIAN RATINGS FRE (in French)”, please see page 38 in the French side of this user’s guide. 38 Initial Setup Set Lock Code Channel guard and V-Chip settings are protected by a four-digit lock code. Your TV comes preset with a lock code of “0000”. You may change the code to any four-digit number you wish. To change the lock code, follow the steps below. Press the MENU button .† To SET LOCK CODE v® To operate (lock icon appears) Press ZERO to access the lock code The first digit will be highlighted v® To select the number .† To move to the next digit Continue to follow these directions for all four numbers Press the OK button to finish (your lock code is now set) Press the Menu button when finished LOCK CODESET LOCK CODESELECTOPERATEEXITMENUPRESS TO FINISH0000OK When a viewer attempts to watch a blocked channel, this message appears: The channel will remain blocked until the correct lock code is entered (see above for information on setting your lock code). THIS PROGRAMMING EXCEEDSYOUR RATING LIMITS. PLEASE ENTER LOCK CODE BY10 KEY PAD TO UNLOCK IT. NO. - - - - Notes: • After a power interruption you must reset the lock code. • Write your lock code number down and keep it hidden from potential viewers. • If you forget the lock code, a new code may be set using the steps listed above. 39 Initial Setup Adjusting CRT Color Convergence This TV has three color projection tubes: one for red, green, and blue. When mixed together in the proper portions, the output of these three color tubes can produce any color. To produce these colors, however, the beams must be precisely aligned over each other so that the colors can be mixed. The produce of aligning these picture beams is called “convergence”. Attention: • Please have your TV on for at least 20 minutes before using this feature. • This adjustment will be needed only when the colors of the characters/lines are separated and lack in distinction. If not, please don’t perform the adjustment. Colors may become separated after the TV has been moved, or over a long period of time if regularly subjected to low levels of vibrations. If the colors become separated, please perform the adjustments below again. In the beginning, please be sure to perform AUTO convergence adjustment. Press the MENU button .† To CONVERGENCE v® To Enter .† To select “AUTO” (The convergence adjustment will start. It will take about 50 seconds). When the adjustment is finished, it will return to what you were watching. Note: • You can reset the adjustment if you do not like the results. See the next page. • If you want to adjust it more, you can perform the manual color convergence adjustment. See the next page. • You can also access this feature by pressing the SUPER FOCUS button on the front panel of your TV. .............................................................................................................................. .............................................................................................................................. Auto MENUCHANNELVOLUMESUPERFOCUSOPERATE– +– + INPUT- 4S-VIDEOVIDEOAUDIORL / MONOOVEROPENSUPERFOCUS 40 Initial Setup .............................................................................................................................. Adjusting CRT Color Convergence (continued...) Manual Press the MENU button .† To CONVERGENCE v® To Enter .† To choose MANUAL v® To Enter If all the lines are white, no convergence adjustment is necessary. If not, you need to perform the manual color convergence below. Select the location you want to adjust by using the number buttons on the remote control. You can select any of the 81 points. Press the SELECT button to change the color of the box to the color of the cross you wish to adjust (red or blue). .† v® Adjust the position of the cross. Adjust the three color crosses until they overlap and appear as a single white cross. Press the OK button Notes: • When you adjust the convergence, mak...
Эта инструкция также подходит к моделям:Телевизоры - AV-56P585 (2.9 mb)
Телевизоры - AV 56P575 (2.9 mb)