Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Make sure that all safety factors regarding strength of installation are observed. • If the installation strength is insufficient, the display may fall down and personal injury may result. Do not install in places which are unable to bear loads. • If the strength of the installation surface is insufficient, the display may fall down and personal injury may result. CAUTION Do not install in places which are subject to humidity, dust, oil fumes, water vapour or excessive heat. • These can have adverse effects on Wide Plasma Display operation, and fire or electric shocks may result. Do not install the Wide Plasma Display face up, sideways or upside down. • Doing so may cause heat to build up inside the display, and fire may result. Two people are required to install and remove the display. • If two people are not present, the display may be dropped, and personal injury may result. Maintain a space of at least 3 15/16 inches at the top, bottom and sides of the display, and at least 211/64 inches at the rear of the display. • The display has air outlet holes at the top and air intake holes at the bottom and rear. These holes must not be covered, otherwise fire may result. Components Wall-hanging bracket unit ........1 Allen key (accessory) ......1 Fixing screw ( M5-35)........................2 (Fixing screw) Insulating spacer ....................................4 Toothed pan washer ....................................4 Pan head bolt with hex socket (M8-45) .........4 Points to note during installation • The wall-hanging bracket is for use in installing the Wide Plasma Display to a vertical wall for viewing purposes. Do not use it for any type of installation other than vertical wall installation. • In order to ensure correct, problem-free operation of the Wide Plasma Display , do not install the Display in any of the following places. • Places which are next to sprinklers or sensors • Places which are subject to vibration or shocks • Places which are close to high-voltage wires or electric motors • Places in direct contact with air from heaters • When installing this wall-hanging bracket unit, use a fixing method appropriate to the type of wall. • Insert the power cord plug for the Wide Plasma Display into a wall outlet which is close and easily accessible. • Provide adequate ventilation so that the temperature around the display does not rise above 40°C (104 F°). If there is insufficient movement of the air inside display, heat may build up inside the display, and fire may result. English Installation procedure English 1. Check the strength of the installation location. The wall-hanging bracket weighs approximately 19.85 lds. and the Wide Plasma Display unit weighs approximately 99.2 lbs. While referring to the wall-hanging bracket installation dimensions in the diagram below, check the strength of the wall in six installation locations, and add reinforcing if any of these locations are not strong enough. • The wall-hanging bracket has installation holes provided in 14 locations. NoteNote 365/8 19 19 / 64 17 23 / 32 1 31 / 32 1 1 / 4 51 / 64 51 / 64 1723/321723/32 315/16 19/32 19/32 Wall installation holes (6 locations) Used for routing wires behind a wall 131/32 Units : inches If the wall material will not allow sufficient strength to be obtained from using six installation holes, use some of the spare holes. However, depending on the construction material used at the place of installation, cracks may develop if the screws are inserted too close to each other. 2. Install the wall-hanging bracket to the wall. • Install the wall-hanging bracket so that the arrow shown on the bracket is pointing upwards. • If it is necessary to embed bolts or nuts beforehand because the wall is made from concrete, use the bracket itself to determine the correct installation hole positions, or use the dimension diagram to calculate the hole positions. Then embed the M6 bolts or nuts into the holes. Furthermore, when embedding the bolts, allow the bolts to protrude from the wall by 13/32 inches to 19/32 inches. Installation procedure First screw a bolt into the centre- top hole. Use a level gauge to correct the alignment of the wall-hanging bracket, and then screw bolts into the remaining five holes. NoteNote • Use commercially-available M6 bolts which suit the wall materials for installation to the wall. 10 NoteNote 3. Adjusting the angle of the wall-hanging bracket Pan head bolt wih hex socket Toothed pan washer Insulating spacer English 5° tilt 15° tilt No tilt Stay 4. Prepare the Wide Plasma Display. • Attach the insulating spacers to the display. Remove the four bolts. The angle for this wall-hanging bracket can be adjusted to one of five positions ranging from no tilt to 20° tilt in steps of 5°. At the time of shipment from the factory, the angle of tilt is set to 5°. To change this angle, you should change the installation position of the stay. * The stay is not needed if installing the display with no tilt. Angle adjustment...