Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
1. Double-click the EMP NS Connection icon in your Applications folder. You see a screen similar to the following: Select projector This box indicates projector status If the connection is working properly, you see your projector listed. If you have additional EPSON projectors on the network, they are also listed. The color of the status icon next to each projector’s name indicates its status: ¦ Gray—The projector is not connected ¦ Orange—The projector is connected to another computer ¦ Green—The projector is connected to your computer 2. Select your projector and click Connect. If more than one projector is listed, you can select up to four projectors and connect to them at the same time. 3. If you turned the projector keyword on when setting up the projector, enter it when prompted and click OK. (It’s the four-digit number displayed at the bottom of your projector screen.) note You can connect to a projector that is being used by another person; however, doing so automatically disconnects the other user. If you assign a keyword to the projector, only people in the same room as the projector can connect to it, so you won’t be disconnected during a presentation. Once the connection is established, your computer’s desktop and note a floating control bar are projected: Position your pointer over a button for a description of its function. For more detailed descriptions, see the User’s Guide. 4. If necessary, drag the control bar out of the way, or minimize it. 5. When done with your presentation, click Disconnect on the control bar. Solving Connection Problems If you don’t see your projector in the EMP NS Connection window, try the following: ¦ Make sure the EPSON 802.11b card is inserted in the projector; see the User’s Guide for instructions. If you have to insert the card, restart EMP NS Connection, or the program will not be able to detect the projector. ¦ Make sure you aren’t projecting one of the EasyMP configuration screens. You should see a message that the projector is ready to connect. If you have to exit a configuration screen, restart EMP NS Connection. ¦ Click the AirPort icon on the Application bar at the top of your Macintosh desktop to make sure you’re trying to connect to the right network. The projector’s ESSID should be displayed and selected. ¦ Make sure AirPort is turned on. Click the AirPort icon on the Application bar and select AirPort: On if necessary. If you don’t see the AirPort icon, follow the instructions beginning on page 5 to enable AirPort. ¦ If possible, move your projector, Macintosh, and base station (if you’re using one) closer together. ¦ If you’re using Access Point (infrastructure) mode and you’re connecting to the wrong network, you may be experiencing signal interference from another network. Open the Applications folder on your hard drive, then double-click the Utilities folder. Double-click AirPort Admin Utility. If you don’t see your base station listed, reset the base station (see the instructions that came with your base station). If your base station is listed, check its name and IP address. Your projector should have the same ESSID name, and the first three segments of the projector’s IP address should be identical to the first three segments of the base station’s IP address. The last segment of the projector’s IP address should be close, but not identical to the last segment of the base station’s IP address. In addition, the projector’s gateway address should be identical to the base station’s IP address. See the User’s Guide for instructions on setting up the projector in Access Point mode. ¦ If you’re unable to connect to the projector, use IP Connect Mode to connect manually. See the User’s Guide for instructions. ¦ Check the Network Configuration tab for your AirPort base station. If you set up your projector to connect in DHCP mode, Distribute IP Addresses and Start a Single IP Address should both be on. See your AirPort documentation for details about configuring your base station. note In Access Point mode, your projector’s ESSID name and IP number are shown at the bottom of the EasyMP Network Screen. ...
Эта инструкция также подходит к моделям:Телевизоры - PowerLite 850p (513.69 kb)