Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
IMPORTANT: 2 1 4 Item No.:PSW501SF the facing of a quilt MADE IN CHINA Pyle Audio 1600 63rd st , Brooklyn, NY, 11204 (718)236-8000 Hardware List: Actual parts appearance and the quantity may different with illustrated. After determining the height of stand, follow the installation instructions in below to install wall mount to different kinds of wall Using a awl or nail to make where the nails are located, as shown as Fig.3b. Distance between two nails for fixing wall mount must not less than 16 . Slide the plate into position as required.(Fig.3c) Pre-drill these holes with a 5mm drill bit to at least 40mm in deep hole. Use wall mount as a template to mark the location of other three holes and drill the same holes. Fix the wall mount to the wall with 4 long bolts(H) and washers(J) . -wooden, brick, concrete and stone. Please make sure these holes are level and eudipleural. by Box wrench(5) ” Wooden wall: -2- -7- A-F G H I J K Fig 3b Fig 3c Brick, wall: Using a awl or nail to make where the nails are located. Distance between two nails for fixing wall mount must not less than 16 . Slide the plate into position as required. (Fig.3c) Pre-drill these holes with a 10mm drill bit to at least 50mm in deep hole. Use wall mount as a template to mark the location of other three holes and drill the same holes. Please make sure these holes are level and eudipleural. Insert wall anchors(I) into each of these holes. Attach the wall mount to the wall using 4 long bolts(H) and washers(J) by Box wrench(5). ” Concrete and Stone 1 2 4 2 3 Fig 3d Balance-adjusting H J 1 Using balance-adjusting system on the plate, make sure whether wall plate is installed balance. If not, then slide the wall plate let pointer level in the center position. Plate 4 4 H I J K 4 4 Square washer Long bolt Wall anchor Long bolt washer Spacer ID Description 1 2 A 3 4 5 B C 1 2 4 1 2 1 4 4 Wall mount Bracket M4.12mm bolt M4.16mm bolt M5.16mm bolt M6.16mm bolt M5.36mm bolt M6.36mm bolt Qty D 4 4 4 4 E F G Cable Cover Safe bolt Box wrench ID Qty Description 5 5 -6- -3- b 15 degree viewing angle eyelevel a Fig 3a First, determine the height of stand The best height of stand is parallel to eyelevel of a person who sitting on a couch. Normally, the horizontal distance of eyelevel is about 4’ from ground level. The following two conditions are for determining the perfect height of stand: 1) the distance between wall and couch(Fig 3a). 2) the distance of eyelevel from ground level plus the distance measured from eyelevel of a person sitting on couch with viewing angle of 15 (Fig 3a). For example: 1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’ 2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’ 3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’ The perfect height of stand centre will be anywhere within b, where you feel comfortable for viewing. ° Step 3: Attach mount to wall WARNING We are not responsible for any personal injury or product damage due to mishandling, incorrect mounting, incorrect assembly or incorrect use of this product. The supplied wall mounting hardware is not for use on steel stud walls or cold cinder block walls. If you are uncertain about the nature of your wall, please consult a qualified contractor. If the hardware you required is not included please contact your local hardware store. Note: Caution: This Product LCD /PlasmaWall Mount Bracket is intended for use only with the maximum weights indicated .See apparatus instructions .Use with products heavier than the maximum weights indicated may result in instability causing possible injury . Check your TV manual to confirm the diameter of bolt to be used or choose an appropriate bolt according to size, height and position of the holes on your TV. See pages 4-5 of these instructions for examples. For correct installing, make sure that hook of every bracket must facing down. Use selected bolts, spacers and washers for installing bracket at the back of display. Adjust two brackets to equal heights and level. Once aligned, tightly secure the bolts. Don't force the bolt into the hole, which will cause a damage of equipments and injure of person. Don't use electric drill to fasten any bolts. IMPORTANT: Step 1: Attach bracket to TV IMPORTANT Step 2: Install the Cable Cover Route the cables as required. Snap the cable cover into place onto the rods (Fig. 2a), and then slide the cover into position as required. (Fig. 2b) Fig 2a Fig 2a Fig 1a M4 Fig bit M5 Fig bit M6 Fig bit Fig 1b 2. Some displays have curved backs with recessed mounting lands(Fig.a). It will require the use of spacer. For this display, install a spacer(K) between display and the bracket. As shown in Fig 1b. Fig a -4- -5- M5 Fig bit M6 Fig bit A,B 2 G D 2 G G C E 2 G K 2 G F K Following examples shows how to use bolts, spacers and square washers. 1.Some displays have vertical backs. No spacer is required. Install the bracket directly to the back of display by usin...