Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
2.LIGHT Press to illuminate the buttons. 3.ON / OFF Press to turn the projector on or off. 4.ENT (Enter) Press to select a highlighted menu item or confirm a changed setting. Note On some remote control units, this button is where the RETURN/EXIT button (item #6) appears here. 5.Cursor Buttons (, , , ) Use these buttons to select items or settings, adjust settings or switch display patterns. When no menu is present on-screen, the UP and DOWN buttons toggle through the available aspect ratios, in this order: UP Button = 16:9 - Standard (4:3) - Letterbox - IntelliWide - Cinema - IntelliWide 2.35 DOWN Button = IntelliWide 2.35 - Cinema - IntelliWide - Letterbox - Standard (4:3) - 16:9 Note Intelliwide 2.35 is available only on the Vision 140/150/CineWide. For more information about aspect ratios, refer to Table 4-1. Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in this order: LEFT Button = HDMI 2 - HDMI 1 - HD/RGB2 - HD/RGB 1 - Component SD - S-Video 2 - S-Video 1 - Composite RIGHT Button = Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - HDMI 1 - HDMI 2 Note The “direct select” function of the UP, DOWN, LEFT and RIGHT buttons is available only on the analog inputs (HD/RGB, SD Component, Composite and S-Video). 6.RETURN/EXIT Press this button to exit the current menu and return to the previous one, or to cancel an operation. Note On some remote control units, the ENT (Enter) button (item #4) is in this location. 7.MENU Press this button to access the OSD controls. Memory Preset Buttons: 8.ISF NT (Night) Press to recall settings for the current input from the “ISF Night” memory preset. 9.ISF DAY Press to recall settings for the current input from the “ISF Day” memory preset. 10.CUST 2 Press to recall settings for the current input from the “Custom 2” memory preset. 11.CUST 1 Press to recall settings for the current input from the “Custom 1” memory preset. 12.VIDEO (1) Press to select Composite video input as the source or to enter the numeric character “1.” 13.S-VID 1 (2) / S-VID 2 (5) (S-Video) Press to select an S-Video input or to enter the numeric character “2” or “5.” 14.COMP (Component) (3) Press to select Component SD (480i/576i) video input as the source or to enter the numeric character “3.” 15.HD 1 (4) / HD 2 (7) Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “4” or “7.” 16.HDMI 1 (6) / HDMI 2 (8) Press to select a Digital Video input or to enter the numeric character “6” or “8.” Aspect Ratio Selection Buttons: Use these buttons to select an aspect ratio directly or to enter numeric characters, as follows: 17.16:9 (9) For viewing 16:9 DVDs or HDTV programs in their native aspect ratio. 18.4:3 (0) Scales the input signal to fit 4:3 display mode in the center of the screen. 19.LETBOX (Letterbox) For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen. 20.I-WIDE (IntelliWide) Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display. 21.CINEMA For viewing 2.35:1 source material. 22.SVC (CineWide-equipped projectors only) Selects the IntelliWide 2.35 aspect ratio, used for viewing 16:9 source material on a 2.35:1 screen. Notes: 3Installation 3.1 Remote Control Battery Installation To install batteries in the remote control: 1.Remove the battery cover from the back of the remote control. 2.Insert the batteries included with the remote control. Ensure that the polarities correctly match the and markings inside the battery compartment. 3.Replace the battery cover. Note 1. Do not mix an old battery with a new one or different types of batteries. 2. If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage. Notes on Remote Control Operation The remote control can be used to control the Vision 140/150 within the ranges shown in Figure 3-1. Component SD NTSC 480i16:9 Approx. 7m/23ft HD1HD2S-VID2S-VID1HDMI1HDMI2VIDEOISFDAYISFNTCUST1CUST2MEMORYRETURNEXITMENUCOMPSOURCE SELECTIONANA4x3LETBOXI-WIDECINEMALIGHTOFFONSVCASPECT12345678ENT Figure 3-1. Available Range of the Remote Control •Do not drop the remote control or expose it to moisture or high temperature. •The remote control may malfunction under a fluorescent lamp. If that occurs, move the VHD Controller away from the fluorescent lamp. •Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the VHD Controller or projector. •If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones. •The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. •Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the VHD Controller, and repeat the operation. 3.2 Quick Setup Table 3-1 gives a quick overview of the Vision 140/150 installation pro...
Эта инструкция также подходит к моделям:Телевизоры - Vision 150 (4.51 mb)