Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Connecting an Antenna If your antenna ends in a single coaxial lead, simply press or screw the cable onto the antenna terminal on the back of your TV. If your antenna ends in a pair of 300 ohm twin leads, you must use a 300-ohm/75-ohm adapter(available at your local electronics store). Place the leads underneath the screws on the adapter, tighten the screws, then press the adapter onto the antenna terminal on the back of the TV. 6 Chapter 2 : Connecting an Antenna or Cable to Your TV If your cable system requires you to use a converter box for all channels, connect the incoming cable to the IN terminal on the converter box. Connect another cable between the OUT terminal on the converter box and the antenna terminal on the TV. You will need to keep your TV tuned to channel 3 or 4 and change channels using the converter box. If your cable system only requires you to use a converter box for some channels (i. e. pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this cable into a splitter (available at your local electronics store). Connect one coaxial cable between one OUT terminal on the splitter and the IN terminal on the converter box. Connect another coaxial cable between the other OUT terminal on the splitter and the B-IN terminal on an A/B switch (available at your local electronics store.) Connect a third coaxial cable between the OUT terminal on the converter box and the A-IN terminal on the A/B switch. Finally, connect a coaxial cable between the OUT terminal on the A/B switch and the antenna terminal on the back of your TV. When the A/B switch is in the A position, you need to change channels on the converter box (and your TV should be tuned to channel 3 or 4); when the A/B switch is in the B position you can change channels on the TV. Connecting Other Pieces of Equipment You may want to connect a VCR, laser disc player, satellite receiver, or another type of equipment to your TV. We recommend that you follow the instructions included with the piece of equipment you wish to connect. Safety Note If you plan on being away from your home for an extended period of time, or if a thunderstorm is approaching, you should unplug your television, and you may wish to disconnect your TV from a rooftop or satellite antenna. You do not need to disconnect your TV from a cable system. 8 Chapter 2 : Connecting an Antenna or Cable to Your TV Changing Channels You can change channels in three ways: 1 1 The WCHV buttons will take you through all memorized channels, one by one. The WCHV buttons will not access channels that have 2 not been programmed into the TV's memory. For more information about programming channels into memory, see the section 3 “Programming your TV's Channel Memory” on the previous page. 2 The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter its number; the TV will tune to the new channel when you enter the second digit of the channel. 3 The PREVIOUS button will take you instantly to the last channel you were watching. Changing the Volume 1 To change the volume of the TV set, use the CVOLB buttons on the remote conteroller or on the front panel. 1 2 2 To quickly turn off the sound, press the MUTE button on the remote. The ‘MUTE’ will appear on screen, colored green. To return the volume to its previous level, press MUTE again. 10 Chapter 3: Operating Your TV Changing the TV's Input Normally, your TV displays the signal coming through the antenna terminal. However, If you’ve connected another component to your TV(such as a VCR) using the Video/Audio input, you will want to be able to view the signal from the component. To do this, you will need to switch from the ‘ TV ’ input to the ‘Line1, Line2’ Input, as follows. 1 With the TV on, press the MENU button twice, then “ Set-Up ” menu will appear. 2 Use the WCHV buttons to select “ Input ”. 3 Press the CVOLB buttons to change from ‘ TV ’ to ‘Line1, Line2’. 4 Wait 10 seconds, or press the MENU button to return to normal TV viewing. Select Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Input : TV Adjust Next 2 Select Set-Up Language : English Input : Line1 Adjust Next 3-1 Select Set-Up Language : English Input : Line2 Adjust Next 3-2 12 Chapter 3: Operating Your TV Returning to the factory settings If you would like to return to the original video settings, as they were calibrated at the factory, follow these steps : 1 With the TV on, press the MENU button. then “Video” menu will appear. 2 Press the CVOLB buttons to set the “Settings” to ‘Preset’. The TV will remember the ‘Custom’ settings you had previously chosen. When you set “Settings” to ‘Custom’ again, your previous custom settings will be restored. Select Settings : Custom Contrast Brightness Sharpness Color Tint Adjust Next 1 Select Video Settings : Preset Contrast Brightness Sharpness Color Tint Adjust Next 2 Descriptions of video settings The contrast setting cont...