Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Телевизоры - LW22N23N (293.26 kb)
Телевизоры - LW22N23N (4.6 mb)
Фрагмент инструкции
10mW Output (3.5o Stereo Jack 32) Frequency RF: 80Hz ~ 15kHz (at- 3dB) Response A/V: 80Hz ~ 20kHz (at - 3dB) English-58 04-BN68-00574C-00Eng.qxd 2/11/04 8:27 AM Page 59 Display Modes If the signal from the system equals the standard signal mode, the screen is adjusted automatically. If the signal from the system does not equal the standard signal mode, adjust the mode with reference to the Video card user guide, as the screen may not display or only the power LED may be on. For the display modes listed below, the screen image has been optimised during manufacture. Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V) Macintosh 640 X 480 832 X 624 35.000 49.726 66.667 74.551 30.240 49.500 - / + / + IBM 640 X 480 720 X 400 31.496 31.469 59.940 70.087 25.175 28.322 - / - / VESA 640 X 480 640 X 480 640 X 480 800 X 600 800 X 600 800 X 600 800 X 600 800 X 600 1024 X 768 1024 X 768 1024 X 768 1024 X 768 37.861 37.500 43.269 35.156 37.879 48.077 46.875 53.674 48.363 56.476 60.023 68.677 72.809 75.000 85.008 56.250 60.317 72.188 75.000 85.061 60.004 70.069 75.029 84.997 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 65.000 75.000 78.750 94.500 - / - / - / + / + / + + / + + / + - / - / - / + / + + / + GTF 1280 X 720 44.769 60.000 74.841 - / + English-59 04-BN68-00574C-00Eng.qxd 2/11/04 8:27 AM Page 60 Maintenance of Your Television To avoid risk of electric shock, do not disassemble the TV cabinet. Users must not service the TV. User maintenance is restricted to cleaning, as explained below: Unplug the television from the power outlet before cleaning. . When you clean the TFT-LCD and the external panel, please apply the recommended small amount of cleaner, using a soft, dry cloth to polish it. Do not force your television screen, scrubbing it only softly. The use of excessive force can result in stains on the screen. . Never use flammable cleaning material to clean your television or any other electrical apparatus. English-60 English-61 How to connect the cables and stand base Do NOT lift the TV set by the stand. The stand is not screwed to the TV set and lifting the set by the stand may cause injury. Remove the cover as shown in the picture. 1 Connect the cables as shown in the picture. 2 3 Replace the cover. Attach the stand to the TV set as shown in the picture. Note : The curved side of the stand base should be placed at the back of the TV set as shown in the above figure. 4 04-BN68-00574C-00Eng.qxd 2/17/04 2:43 AM Page 61 04-BN68-00574C-00Eng.qxd 2/11/04 8:27 AM Page 62 Setting Up Your Remote Control After it has been set up properly, your remote control can operate in four different modes: TV, VCR, Cable, or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Note The remote control might not be compatible with all DVD Players, VCRs and Cable boxes. Setting Up the Remote to Operate Your VCR. 1 Turn off your VCR. 2 Press the SELECT button and make sure that the VCR LED is illuminated. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the VCR code listed on page 65 of this manual for your brand of VCR. Make sure you enter three digits of the code, even if the first digit is a “0”. (If more than one code is listed, try the first one.) 5 Press the Power button on the remote control. Your VCR should turn on if your remote is set up correctly. If your VCR does not turn on after set up, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000 through 088. Note on Using Remote Control Modes: VCR When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume. English-62 04-BN68-00574C-00Eng.qxd 2/11/04 8:27 AM Page 63 Setting Up Your Remote Control Setting Up the Remote to Operate Your Cable Box. 1 Turn off your cable box. 2 Press the SELECT button and make sure that the Cable LED is illuminated. 3 Press the SET button on your TV’s remote control. 4 Using the number buttons on your remote control, enter three digits of the cable box code listed on page 65 of this manual for your brand of cable box. Make sure you enter three digits of the code, even if the first digit is a “0”. If there is more than one code listed, try the first one. 5 Press the Power button on the remote control. Your cable box should turn on if your remote is set up correctly. If your cable box does not turn on after set up, repeat steps 2, 3, and 4, but try one of the other codes listed for your brand of cable box. If no other codes are listed, try each code, 000 through 077. Note on Using Remote Control Modes: Cable Box When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume. English-63 04-BN68-00574C-00Eng.qxd 2/11/04 8:27 AM Page 64 Setting Up Your R...