Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Multi-family Dwellings/Apartments (Connect to wall antenna socket) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Outdoor Antenna (VHF, UH F) Wall Antenna Socket RF Coaxial Wire (75 .) Antenna UH F Signal Amplifier VHF ¦¦ In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above. ¦¦ If signal needs to be split for two TVs,use an antenna signal splitter for connection. SERUVSICBE IONNLY RS-232C IN (CONTROL&SERVICE) A(URGDBI/OD VIIN) OPTICAL DIGITAL AUDIO OUT ACNATBELNEN AI/N VIDEO AUDIO VIDEO AUDIO RGB IN (PC) L(MONO) R 2 1 (DVI) AV IN COMPONENT IN L R /DVI IN COMPONENT IN VIDEO AUDIO L(MONO) AUDIO R AV IN VIDEO IN OUT VARIABLE AUDIO OUT ANTENNA IN HDMI/DVI IN RGB IN (PC) RS-232C IN (CONTROL) AUDIO IN (RGB/DVI) USB IN SERVICE ONLY VIDEO AUDIO L(MONO) AUDIO R AV VIDEO IN1 OUT VARIABLE AUDIO OUT ANTENNA IN HDMI /DVI IN RGB IN (PC) RS-232C IN (CONTROL) AUDIO IN (RGB/DVI) USB IN SERVICE ONLY 1 HDMI 1 2 AV IN2 IN 3 COMPONENT IN E X T E R N A L E Q U I P M E N T S E T U P exteRnAl equIPment setuP ¦ To avoid damaging any equipment, never plug in any power cord until you have finished connecting all equipment. ¦ This section on exteRnAl equIPment setuP mainly uses diagrams for the 32LH2*** models. ¦ Image shown may differ from your TV. ConneCtIng WIth A ComPonent CABle This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below. (RGB) SPEAKEROUTVOLUME CONTROL12/DVIINSTEREO(8 ) 1 2 Connect the video outputs (Y, PB, PR) of the 1 external equipment (digital set-top box, DVD, etc.) to the ComPonent In VIdeo jacks on the TV. Connect the audio output of the external equip ment (digital set-top box, DVD, etc.) to the ComPonent In AudIo jacks on the TV. Turn on the external equipment. (Refer to the external equipment's manual for operating instructions.) Select the Component input source using the 2 3 4 InPut button on the remote control. > HDMI Audio Supported format : Dolby Digital, PCM DTS Audio format is not supported. Signal Component HDMI 480i/576i O X 480p/576p O O 720p/1080i O O 1080p O (50 Hz / 60 Hz only) O (24 Hz / 30 Hz / 50 Hz / 60 Hz) Component Input ports To achieve better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y PB PR Y PB PR Video output ports Y B-Y R-Y on DVD player Y Y Cb Cr Pb Pr 3 external equipment setup Connecting with an HDMI cable NOTE >>The TV can receive video and audio signals simultaneously when using an HDMI cable. >>If the DVD does not support Auto HDMI , you must set the output resolution appropriately. >>Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable. 1 Connect the HDMI output of the external equipment (digital settop box, DVD, etc.) to HDMI/DVI IN 1, HDMI 2 (Except for 19/22LH2***) jack on the TV. 2 Turn on the external equipment. (Refer to the external equipment's manual for operating instructions.) 3 Select HDMI1, HDMI2 (Except for 19/22LH2***) input source using the INP UT button on the remote control. (RGB) SPEAKER OUT VOLUME CONTROL 1 2 /DVI IN (8 ) 1 2 /DVI IN 1 Connect the external speaker to the Speaker output(STEREO ) jack on the TV. 1 Method of Volume control port Cable Spec. GND / Up / Down • Each Up/ Down pin is pulled to 3.3V with CPU GPI O. • CPU detects transition from 3.3V to GND level for volume control. Speaker output Setup VOLUME CONTROL STEREO (8 ) SPEAKER OUT (RGB) 1 1 Control port for Speaker out UP DOWN GND RI GHT LE FT GND external eqUipMent SetUp ConneCting with an hDMi to DVi Cable external equipment setup (RGB) SPEAKEROUTVOLUME CONTROL12/DVIIN(8 ) 1 2 or 1 Connect the digital set-top box or the DVi output of the pC to hDMi/DVi in 1 jack on the tV. 2 3 4 Connect the audio output of the digital set-top box or the pC audio output to the aUDio in (rgb/DVi) jack on the tV. turn on the digital set-top box or the pC and the tV. (refer to the digital set-top box or the pC manual for operating instructions.) select hDMi1 input source using the inpUt button on the remote control. ConneCting with a eUro SCart Cable external equipment setup scart input Output Video audio rGB Video, audio aV O O O analogue tV, Digital tV Output type Current input model aV (tV Out) Digital tV Digital tV analogue tV, aV analogue tV Component/rGB analogue tV HDmi analogue tV > tV Out : Outputs analogue tV or Digital tV signals. 1 Connect the euro scart socket of the external equipment (DVD, VCr, etc.) to the aV euro scart socket on the tV. 2 turn on the external equipment. (refer to the external equipment's manual for operating instructions.) 3 select aV input source using the inpUt button on the remote control. ANTENNAIN(RGB)...
Эта инструкция также подходит к моделям:Телевизоры - 42LH200H (17.39 mb)
Телевизоры - 42LH250C (17.39 mb)