Производитель: LG Размер: 1.89 mb Название файла: Язык инструкции:

Перейти к скачиванию

* Be careful not to install a TV that exceeds the weight restrictions of the wall mount. * Be careful with the tools used during installation to prevent accidents or damage. 4 1 Separating the TV bracket 1. After expanding the wall mount forward as shown in Fig. 1, separate the safety pin from the wall mount as shown in Fig. 2. 2. Separate the set bracket as shown in Fig. 3. Safety pin 1 2 3 Installation method - Tools you will need : Phillips head "+" driver(Manual or motorized) O4mm drill bit for wood or steel / Level / Stud finder / Drill. You may also need an 8mm socket wrench or an 8mm drill bit for concrete. 2 Attaching the mounting bracket on the TV Make sure the screws are fully tightened to the bracket and display. If the screws will not fully tightened, they might be too long or the wrong size. 1. Check to see if the display has screws already installed into the VESA mounting holes. If so, remove those. 2. Attach the bracket to the back of the display as shown above. Use a Phillips head "+" screwdriver to tighten the screws. - At this time, be careful to prevent the set from falling down. - Make sure the screws are fully tightened to the bracket and display. VESA 100X100 / VESA 200X100 is supported. If needed, you may refer to the display's user manual to verify the display has one of the supported VESA formats. Bracket to attach to the display VESA 200 VESA 100 VESA 100 Install the PVC washer between the brackets and the display on the following models : 32LE53*/32LE55* But for 26LE53*/26LE55* model, this is provided as TV component. > > > > M4 X 10mm : 19/22LD*, 19/22LE*, 19/22LX*, 19/22LK*, 19/22LZ*, 19/22LW*, 19/22LV*, 26LE65* M4 X 14mm : 26/32LD*, 26/32LE*(Excludes 26LE65*), 26/32LX*, 26/32LK*, 26/32LZ*, 26/32LW*, 26/32LV* Screws are included for the following models: 5 ENGLISH 3 How to attach to masonry walls - Check the material of the wall and the thickness of the finishing. - When installing the product on the wooden wall, refer to page 6. - When installing the product on wall material not designated, install the product so that each fixated location can withstand the pull out load of 70kgf (686N) and shear load of 10kgf (980N) or above. - Use the O8mm drill bit for concrete and hammer (Impact) drill. Please follow the below direction. a b d e a. Use a drill bit O8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm. b. Clean the drilled hole. c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.) d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward. e. Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque of 45 - 60 kgf/cm. Wall mount screw c Anchor - Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. 4 How to install the wall mount > When you separate the 4 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier to install the product. > When installing the product on a masonry wall, turn the 4 screws on the A part counterclockwise to separate the screw and bracket. > After aligning the wall bracket to the location to install, mark the part to screw on the wall and then remove the wall bracket. > Refer to page 4 to attach the wall bracket. > Use a level to check whether the wall mount is level. Separate the wall mount screw. Wall mount screw > f the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the closest location. But, do not change 2 or more locations from the designated spot. > Assemble the wall mount screw on 1 left and 1 right location on the top part and 1 left and 1 right location on the bottom part. > At this time, use a "+" driver (Manual or motorized) or 8mm wrench to tighten the screw so that the wall, wall bracket and screw are completely pressed against one another. A 6 Safety pin 406mm drywall > After mounting the display, insert the safety pin as shown. If the safety pin is not fixated as shown in the picture, the display can fall. > After the install is finished, pull the bottom part of the display to verify the product is attached securely. > In using cables or accessories not provided with the wall mount, make sure to keep a certain distance from the wall so that excessive force is not applied on cables or accessories. 6 If the product is not leveled after the installation, you can rotate the display up to 5 degrees. ± 5° ± 5° 7 76mm drywall wood stud a. Locate and mark the centers of the wall studs using a stud finder. b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and then remove the wall bracket. c. Use a level to make sure your screw ma...

Эта инструкция также подходит к моделям:
Телевизоры - LSW100BG (1.89 mb)

Скачать инструкцию

Чтобы скачать, введите 2 цифры: