Оценок - 2, средний балл: 4 ( )

Производитель: Sony Размер: 3.07 mb Название файла: Язык инструкции:

Фото и характеристики  Sony  KDL-55NX725

Inserting batteries into the remote 1 Remove the protection sheet. 2 Push and slide the cover upward. 8 GB For KDL-60NX725 For KDL-60NX725 Attaching the Table-Top 1 Align with the two dowels of the Table- Stand Top Stand, and gently place the TV, checking the f mark is facing the front. For KDL-55/46HX925, KDL-55/46HX825, KDL-55/46/40NX725 1 Refer to the supplied Table-Top Stand leaflet for proper attachment for some TV models. 2 Place the TV set on the Table-Top Stand. Guide pins 2 Attach the TV and Table-Top Stand with the supplied screw and hexagon wrench. ~ • Align the TV from the top, slide it in until the guide pins cannot be seen. 3 Fix the TV to the Table-Top Stand according to the arrow marks that guide the screw holes using the supplied screws. * 3 N•m {30 kgf•cm} * Head ~ • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}. ~ • Set the torque setting to approximately 3 N·m {30 kgf·cm}. Getting Started (Continued) 9 GB Detaching the Table-Top Stand from the TV Detaching the Table-Top Stand from the TV fixed in step 3. For KDL-60NX725, be sure to remove the screws for detaching the head when the Table-Top Stand is not attached to the TV. ~ • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. • When removing the Table-Top Stand from the TV, lay the display face down on a stable work surface that is larger than the TV. • To prevent damaging the surface of the LCD display, make sure to place a soft cloth on the work surface. • Be sure the TV is on the vertical position before switching on. TV set must not powered on with LCD panel face down to avoid uneven picture uniformity. 2: Adjusting the viewing angle of the TV This TV can be adjusted within the angles as illustrated. Angle adjustment (Swivel) (except KDL-60NX725) ~ • When adjusting the angle, hold the stand with one hand to avoid having the stand slip or TV tip over. 20° 20° 20° 20° Angle adjustment (Tilt) (except KDL-60NX725) 0° - 6° ~ • Ensure that there are no objects in front of the TV. IR Sensor 3D Sync Transmitter Intelligent Presence Sensor • Do not expose the Intelligent Presence Sensor to direct sunlight or other strong light, as malfunction may occur. 10 GB Connecting a Set Top Box/recorder Connecting a Set Top Box/recorder Connecting an antenna (e.g. DVD recorder) with HDMI (aerial)/Set Top Box/ recorder (e.g. DVD recorder) ~ • Use an antenna cable connector no greater than 14 mm in thickness. • Use an HDMI cable connector within 12 mm (thickness) . 21 mm (width). Connecting a Set Top Box/recorder (e.g. DVD recorder) with SCART SCART adapter (supplied) Set Top Box/recorder (e.g. DVD recorder) Set Top Box/recorder (e.g. DVD recorder) Recommendation of the F type plug The one based on the following drawing is recommended about the F type plug. Projection of the inner wire from the connection part must be less than 1.5 mm. 1.5 mm max. (Reference drawing of the F type plug) Getting Started ~ • Right Angle Type Universal SCART Lead is recommended for this connection. • Screw the satellite connector softly with hand, do not use any tool. • TV must be switched off when connecting satellite antenna (aerial). 11 GB 4: 4: Audio/video device AV/Component adapter (supplied) 1 Install a wood screw (4 mm in diameter, not supplied) in the TV stand. 2 Install a machine screw (M4, not supplied) into the screw hole of the TV. 3 Tie the wood screw and the machine screw with a strong cord (not supplied). The length of the M4 machine screw differs depending on the cord diameter. Please refer to below illustration. Screw M4 Cord 5-6 mm TV’s Table-Top Stand 12 GB 13 GB Getting Started 6: Bundling the cables ~ • Before bundling the cables, remove the cable holder from the AC cover (see step 1 and 2). Reuse the cable holder (see step 3) to bundle the other cables (see step 4). • Do not bundle the AC power cord (mains lead) together with other cables. * When installing on the wall, attach the cable holder under the terminals. 7: Performing the initial set-up 1 Connect the TV to your AC power outlet (mains socket). 2 Check the ENERGY SAVING switch setting is on (z). 3 Press 1 on the TV. The = (power) indicator will light up in green. When you switch on the TV for the first time, the Language menu appears on the screen. ~• When you turn on the TV for the first time, the TV requires some internal processing for optimization before you can perform the initial setup. There will be no picture and sound, and the timer indicator on the front of the TV blinks orange for about 40 seconds. Do not turn off the TV during this process. This process has been completed at the factory for some TVs. Follow the instructions on the screen. 3 4 1 2 * 4 (Continued) Satellite Auto Tuning: Satellite Auto Tuning: 1 Please select “Preferred Satellite” or “General Satellite”. 2 For “Preferred Satellite”, select your preferred operator. “Satellite Auto Tuning” automatically tunes in available sat...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: