Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
This is not a fault in your TV-Video Combi. Searching for tape position without picture (forward wind and rewind) 1. 1.1.Stop the tape with STOP C-L . 2. 2.2.Press REW0-s (reverse) or FWD 1-B (forward). 3. 3.3.To stop the tape, press STOP C-L . Manual tracking To manually adjust the tracking during playback, press PROG P+ PROG P-or P–P+ . Tracking will return to Automatic Tracking Adjustment when you press STOP C-L , insert a tape, or press PLAY B-K . To remove vertical jitter in a Still picture, press P–P+ . 10 EN 6. Manual recording General information Use ‘Manual recording’ to make a spontaneous recording (for example, a programme currently being shown). If you want to start and stop a recording manually, read the section ‘Recording without automatic switch-off’. If you want to start a recording manually but have it stopped automatically, read the section 'Recording with automatic switch-off'.(e.g. not to record to the end of the tape) Recording without automatic switch-off 1. 1.1.Insert a cassette. 2. 2.2.Use P–P+ to select the programme num ber you want to record, for example, ‘P01’. 3. 3.3.To start recording, press REC I . 4. 4.4.Stop recording with STOP C-L . The message ‘PROTECTED CASSETTE CANNOT RECORD’ appears briefly on the screen, then the cassette is ejected. A cassette without its security tab had been inserted. Cover the hole with adhesive tape or insert a new cassette. Recording with automatic switch-off (OTR One-Touch-Recording) 1. 1.1.Insert a cassette. 2. 2.2.Use PROG P+ PROG P– or 0..9 to select the programme number you want to record. 3. 3.3.Press REC I . 4. 4.4.Each time you press REC I you will add 30 minutes to the recording time. 5. 5.5.To stop recording, press STOP C-L . Preventing accidental erasing All cassettes (except rental and pre-recorded cassettes) have a security tab on the back of the cassette. To prevent recording over important recordings (erasing), you can remove this security tab. If you later decide to record on a protected cassette, simply cover the hole with adhesive tape or slide the tab to the right. Lining up recordings (assemble cut) When you add a further recording to a cassette, which already has a recording on it, a short blank (flicker) can appear between the old and the new recording or the picture itself can flicker. To help reduce these from occurring, proceed as follows: 1. 1.1.Find the tape position of the old recording where you want to insert the new recording. 2. 2.2.Look at the last minute of the old recording (playback). 3. 3.3.Press STILL 2 22 at the tape position where the new recording is to go and press REC I . 4. 4.4.Now start recording as usual by pressing REC I on the remote control. 5. 5.5.Stop recording with STOP C-L . Selecting the recording speed (SP or LP) LP allows to double the recording duration on tape (for example six hours instead of three hours on a E180 cassette). 1. 1.1.Switch on the TV. If required, select the programme number for the TV-Video Combi. 2. 2.2.Press MENU . The main menu will appear. 3. 3.3. Select ‘RECORD SETUP’ using PLAY B-K or STOP C-L and confirm with FWD 1-B . 4. 4.4. Select ‘RECORD SPEED’ using PLAY B-K or STOP C-L . SELECT KL CHOOSE B >RECORD SPEED [SP] END=EXIT 5. 5.5.Select the required recording speed with FWD 1-B . ‘SP’ / ‘LP’ ‘SP’: Standard Play (normal recording speed) offers the usual first-class picture quality. ‘LP’: Long Play (half recording speed, double recording time). 6 hours can be recorded on a 3-hour cassette (E180) with a somewhat reduced picture quality. 6. 6.6.To end, press STATUS/EXIT . 11 EN 7. Programming a recording (TIMER) General information Error message : ‘FULL’ • If this error message appears after you select Use a TIMER programming to automatically start ‘ONCE’, ‘DAILY’ or ‘WEEKLY’ on TIMER menu and stop a recording at a later time or date. The and press FWD 1-B , then all TIMER blocks TV-Video Combi will switch to the right pro-are already programmed. No more recordings gramme number and begin recording at the cor-can be programmed. If you want to clear or rect time. With this TV-Video Combi, you can check a programmed recording(TIMER block), pre-programme up to eight recordings within a select the programme number on TIMER LIST period of one year. To make a programmed menu and press CLEAR . recording, your TV-Video Combi needs to know: * the date you want to make the recording * the programme number of the TV channel * the start and stop time of the recording * VPS or PDC on or off [14PV235/21PV385] This information is saved in a ‘TIMER’ block. [14PV235/21PV385] What is ‘VPS/PDC’? ‘VPS’ (Video Programming System)/ ‘PDC’ (Programme Delivery Control) are used to control the start and duration of TV channel recordings. If a TV programme starts earlier or ends later than scheduled, the video recorder will turn on and off at the correct time. What do I need to know about ‘VPS/PDC’? Usually the VPS or PDC time is the same as the start time. But if your TV guide shows a VPS or PDC...
Эта инструкция также подходит к моделям:Телевизоры - 14PV235/01 (194.46 kb)