Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Philips, модель 32PF9956/12

Производитель: Philips
Размер: 1018.49 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


‘ Adjust the volume level of the external subwoofer, presumed this control is present on the subwoofer. See also the instruction manual of the external subwoofer. Side connections VIDEO AUDIO 3 2 1 S•VIDEO USB Camera or Camcorder & Connect your camera or camcorder as shown. e Connect to VIDEO 2 and AUDIO L 3 for mono equipment. For stereo equipment also connect AUDIO R 3. S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-VIDEO input 1 and AUDIO inputs 3. Do not connect cable 1 and 2 at the same time. This may cause picture distortion ! Headphone & Insert the plug into the headphone socket L as shown. e Press ¬ on the remote control to switch off the internal loudspeakers of the TV. The headphone impedance must be between 8 and 4000 Ohm. The headphone socket has a 3.5 mm jack. In the Sound menu select Headphone volume to adjust the headphone volume. USB connector Connect your device with a USB output connector (e.g. a digital camera, a USB memory stick) to the USB connector. 22 (button) (button) (button) (button) (button) (button) (button) (button) To select connected equipment Press the v key on the remote control repeatedly, or select Source in the Setup menu (see p. 10) to select EXT1, EXT2, EXT3, Side or HDMI 1 according to where you connected your equipment. Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on. Recorder Recorder with EasyLink The recorder can be operated with the remote control via the Recorder menu on screen. Rwd Play Stop Play Ffw Rec Eject Op ‡ . † ® I & Press the MENU key on the remote control. e Select the Recorder menu with the cursor up/down. “ Press the cursor left/right, up/down to select one of the recorder functions. The key ® for recording can be operated in the TV mode. If your EasyLink recorder has the system standby function, when you press the B key for 3 seconds, both TV and the recorder are switched to standby. Record with your recorder with EasyLink In TV mode, it is possible to start a direct recording of the programme which is being displayed on the TV screen. Continue to press the ® record key on the remote control for more than 2 seconds. Note: Switching programme numbers on your TV does not disturb recording ! When recording a programme from a peripheral connected to EXT 1, EXT 3 or Side, you can not select another TV programme on the screen without disturbing the recording.. 23 (button) (button) (button) (button) (button) (button) (button) (button) Audio- and video equipment keys Audio- and video equipment keys b ¬ + - V + - v b i 0 h q Select 1 2 3 4 5 6 7 8 9 0 O ‡ . † ® ® ®® . B P AMP DVD/R TV SAT AUX MENU . Active Control OK Browser ® This system remote control operates the following Philips equipment: TV,VCR, DVD, DVD/R, SAT (RC5/RC6), AMP (+TUNER), CD, CD/R. Press the Select key to operate any of the equipment indicated in the display (AUX = CD; DVD/R = DVD, SAT = SAT (RC5). Another device can be selected by pressing Select repeatedly within 2 seconds. The led will blink slowly to indicate the device. Press one of the keys on the remote control to operate the peripheral equipment. To return to TV mode press Select while the led is blinking. When no action is taken within 60 seconds, the remote goes back to TV mode. When you do not want the remote to go back to TV mode, and to stay in the mode selected, proceed as follows: Select the desired mode with the Select key. Wait until no LED is lit. Press the Select key again simultaneously with the OK key for at least 2 seconds. The remote will not go back to TV mode from now on and will remain in the mode selected. To go back to the default setting of the remote (TV mode) repeat what is explained above, selecting the TV mode. Note: When the Select key is pressed and held for more than 2 seconds, the RC5/RC6 system select command is transmitted. B to switch to standby .. for pause (VCR, DVD, CD) RDS news/TA (AMP); to shuffle play (CD/R) ® for record O for rewind (VCR, CD); search down (DVD, AMP) ‡ for stop . for play † for fast forward (VCR, CD); search up (DVD, AMP) b RDS display (AMP); to select your choice of subtitle language (DVD); i display information Additionally the DVD/R, SAT and AUX indicator can be programmed to operate the DVD-R, DVD + receiver, DVD-R + receiver, SAT (RC6), CD-R and VCR instead. & Select TV with the Select key. e To program • DVD-R, press the OK key + digit 2; • SAT (RC6), press the OK key + digit 4; • CD-R, press the OK key + digit 6; • DVD + receiver, press the OK key + digit 7; • DVD-R + receiver, press the OK key + digit 8; • VCR, press the OK key + digit 9. MENU to switch the menu on or off - P + for chapter, channel, track selection 0 to 9 digit entry 0 tape index (VCR), select a DVD title/chapter, select a frequency (AMP) U VCR timer cursor up/down to select the next or the previous disc (CD) cursor left/right to select the previous or following track (CD) search up/down (AMP) “ Select th...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории