Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
To select an age rating, you must first enter your 4-digit child lock code. If no child lock code is set, you can set the code now. When the code is entered, you can select the age rating. When the rating of a programme is equal or higher than the rating you have set for your child's age, the programme will be locked. The TV will ask for the code to unlock the programme. For some operators, the TV only locks programmes with a higher rating. Change code To change the current Child lock code, press h, select S Setup and press OK. Select Satellite settings > Child lock > Change code. Enter the current code and then enter the new code twice. The new code is set. Forgotten your code? To override and enter a new Child lock code in case you forget it, enter 8888. 4.2 Satellite installation What you need Next to DVB-T and DVB-C reception, this TV has a built-in satellite DVB-S/DVB-S2 receiver. If you connect a satellite dish antenna, you can receive digital satellite channels. You do not need an external satellite receiver. LNB An LNB (Low Noise Block-downconverter) captures the signals from a satellite and is mounted at the end of the pole on the dish antenna. The TV can receive signals from 4 different LNBs. Satellite channel installation With a properly set up and connected satellite dish antenna, you can install satellite channels on the TV. Make sure your satellite dish antenna is perfectly aligned. You can install channels from 4 different satellites (4 LNBs). To install the satellite channels, follow the steps 1 to 5. 1 -Install To search for satellites and install satellite channels, press h, select SSetup and press OK. Select Search f or satellite and press OK. If you have already installed satellites, select Reinstall channels and press OK. 2 -Connection type Select the number of satellites you want to install. The TV sets the appropriate connection type automatically. If necessary, you can still adjust the connection type in the Settings later. In the Settings menu select Connection type and select One LNB, if you have only one LNB on your satellite dish. Select DiSEqC Mini, if you have 2 LNBs or select DiSEqC 1.0 for 3 or 4 LNBs. Select Done to close the settings. 3 -Search for satellites To start the search, select Start and press OK. The TV searches for all available satellites. This may take several minutes. If no satellites are found, check the satellite dish connections and the position of the dish antenna. The signal quality shown is not always representative of the signal quality of all channels on that satellite. To repeat the search for satellites, select Search and press OK. If you are satisfied with the satellites found, you can install all their channels. 4 -Install channels To install all channels for the satellites you found, press Install. The installation may take several minutes or half an hour per satellite. 5 -Sorting channels At the end of the installation, depending on the installed satellite, you can choose between different sorting lists for your satellite channels. When the installation is finished, you can find all satellite channels in the All satellite channels list. The channels are also sorted by type in s eparate lists. More settings For most satellites, you do not need to change the LNB related settings but, if you are searching for a specific satellite on C-band, you need to set the LNB you use for this satellite to C-Band LNB. Or, if you are an expert user, you might need a Custom setting for the LNBs you use. To speed up searching for satellites and channels, set the Frequency scan rate to 10MHz. To do a thorough scan, set the rate to 2MHz (recommended for Turkish satellites). Reset You might have lost track of the settings you set up. To reset the satellite installation settings to factory settings, select Reset in Settings and press OK. Manual installation The automatic channel install might have missed a specific channel or channels from a transponder. You can add a transponder manually. Look up and read Manual installation with LList. Dish antenna connection Look up and read about the Dish cable with LList. Watch satellite / Satellite installation Find the list of preset satellites on this TV in LList > Specifications > Power and reception. Add a satellite If satellite channels are already installed, you can add an extra satellite to the installation. You can install channels from 4 different satellites -4 LNBs. 1 -Connection type Check the Connection type setting before you add a satellite. The setting Single receives only one LNB, the setting DiSEqC Mini receives only 2 LNBs and the setting DiSEqC 1.0 can receive 3 or 4 LNBs. To check the Connection type first, press h, select SSetup and press OK. Select Search for satellite > Reinstall channels > Settings and press OK. Select Connection type and select the setting you need for the number of satellites you want to install. Select Done to close the s ettings. Pres s b to close Reinstall channels. 2 -Add a satellite...