Оценок - 0, средний балл: 0 ( )

Производитель: Philips Размер: 4.06 mb Название файла: Язык инструкции:

Connecting a set-top box, DVD recorder via composite connectors and analog audio DVD recorder Set-top box Cable RF IN AUDIO L/R + VIDEO IN OUT OUT IN RF IN RF OUT Do not place your recorder too close to the screen because some recorders can be susceptible to signals. Note • Only the left loudspeaker reproduces sound for mono equipment. Use a mono to stereo adapter (not supplied) for sound reproduction via all internal loudspeakers. • When you connect cables, match the cable colors to the connectors on the TV. 40 EN Connecting a set-top box via a composite connector and analog audio RF IN OUT IN AUDIO L/R + VIDEO Cable Set-top box Note • Only the left loudspeaker reproduces sound for mono equipment. Use a mono to stereo adapter (not supplied) for sound reproduction via all internal loudspeakers. • When you connect cables, match the cable colors to the connectors on the TV. Connecting the TV to the internet using an Ethernet cable LAN LAN WAN 1 2 3 4 5 Hub or broadband router Telecommunications equipment (modem, etc.) Ethernet cable Ethernet cable Internet Note • Please purchase shielded Ethernet cables at your local store and use them when you connect to network equipment. • After connecting an Ethernet cable, set up necessary network settings. (For the network setup, refer to ‘Network’ on page 30.) • Do not insert any cable other than an Ethernet cable to the Ethernet port to avoid damaging the unit. • If your telecommunications equipment (modem, etc.) does not have broadband router functions, connect a broadband router. • If your telecommunications equipment (modem, etc.) has broadband router functions but there is no vacant port, use a hub. • For a broadband router, use a router which supports 10BASE-T / 100BASE-TX. • Do not connect your PC directly to the Ethernet port of this unit. Connecting the TV to the internet using a USB wireless LAN adapter LAN WAN Wireless LAN Access Point (AP) (e.g. wireless router) Network equipment (modem, etc.) Ethernet cable Internet USB wireless LAN adapter Note • After connecting a USB wireless LAN adapter, set up necessary network settings. (For the network setup, refer to ‘Network’ on page 30.) • This unit is compatible with the supplied USB wireless LAN Adapter only. (Commercially available USB wireless LAN adapters are not supported.) • Do not insert the supplied USB wireless LAN adapter when the unit is turned on. Please insert the USB wireless LAN adapter when the unit is in the standby mode or turned off. • Use a Wireless LAN Access Point (AP) (e.g. wireless router) which supports IEEE 802.11 b/g/n. (n is recommended for stable operation of the wireless network.) • This unit does not support Ad-hoc mode. • Other radio devices or obstacles may cause interference to the wireless network connection. • Do not use an extension cord and USB Hub to connect devices to this unit. Always insert the USB fl ash memory or the supplied USB wireless LAN adapter in to this unit directly. Connecting a digital home theater amplifi er using a digital audio coaxial cable digital home theater amplififi er DIGITAL AUDIO IN OUT Note • Due to Copyright restrictions, the broadcaster may choose to mute PCM audio over Digital Audio Output for certain channels, shows or segments during the broadcast. EN 41 English Connecting a PC If you connect a PC with a VGA connector at the back. AUDIO OUT AUDIO IN PC OUT IN VGA If you connect a PC with a HDMI-DVI connector. AUDIO OUT AUDIO IN DVI OUT PC HDMI 1 IN only If you connect a PC with an HDMI connector. PC OUT IN HDMI Add devices After connecting devices, assign the device attached to each connector. This allows you to easily identify devices connected to your TV. 1 Press MENU on the remote control and then use I / i / I / . to select [Add new devices]. 2 Use I / . to select [Start], then press OK. 3 Use I / i to select a device and press OK. 4 Use I / i to select the connector your device is connected to and press OK. 5 If there is video and audio output, press OK. Repeat the procedure until all devices are correctly assigned to connectors. Remove devices If a device is no longer connected to the TV, remove it from the home menu. 1 Press MENU on the remote control. 2 Use I / i / I / . to select a device to remove. 3 Press OPTIONS. 4 Use I / i to select [Remove device], then press OK. 5 Use I / . to select [OK], then press OK. The picture quality of Check the speed of your internet connection.You need speeds 10 Troubleshooting streaming movie (Netflix of at least 8 Mbps to this player for high quality uninterrupted or VUDU) is poor. playback. Problem Possible cause and solution No power or indicator light. No picture or soundis detected from the device using HDMI 1-4input jack. The TV is not connected to the power. Press .POWER at the side of theTV or on the remote control. Ensure that the AC power cord is connected tightly to the TV power connector and to the power socket outlet. Remove the AC power cord from the power socket outlet, wait 60 seco...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: