Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
The TV will continue the upgrade as soon as the power comes back; -If an error occurs during the upgrade you should retry the procedure or contact your Local Customer Service Centre. 5. When the message Operation successful appears, remove the USB portable memory and restart your TV with the power switch B at the side of the TV. Your TV will start up with the new software. Note: once the upgrade is finished use your PC to remove the TV software from your USB portable memory. If you need further assistance or in case of problems, please call your local Philips Customer Centre. See Philips Consumer Care on the website. 61 EN Annex 1 (Continued) TV menu Installation Software upgrade ............. Current softw. info Channels Local upgrades Manual network i.. Announcement Preferences Connections Decoder Factory settings Software upgrade Info Local software upgrade procedure New software, or the currently installed software version, can also be obtained from the website. 1. Go to using the web browser of your PC. 2. Follow the procedure to find the information and the software related to your TV. 3. Select the latest software upgrade file and download it to you PC. 4. Decompress the ZIP-file. Rename the resulting file “autorun.upg” to for ex. “upgrade.upg”. Move the renamed file to the subdirectory “Upgrades”. Remark: if there is no subdirectory “Upgrades” present, please create one. 5. Insert the portable memory that contains the downloaded software upgrade. 6. Select Software Upgrade in the Installation menu. Go to Local upgrades. The TV will list all compatible software available on the USB portable memory and display the data for each selected upgrade version. 7. Select the correct upgrade version and press the red colour key to start the upgrade. Your TV will restart and will automatically go to the upgrade mode. After a few seconds it will display the status of the upgrade procedure. Warning: if you try to upgrade to a software version equal or lower than the current version, a confirmation will be asked. Downgrading to older software should only be done in case of real necessity. 8. When the software upgrade was successful, remove the USB portable memory and restart your TV with the power switch B at the side of the TV. Your TV will start up with the new software. Note: Only use software upgrades that can be found on the website. 62 Annex 2 - Philips TV-Slideshow Format with background music EN Notes: -the latest version of this document can be found on the Philips support website (Use the type number of your TV to find this documentation and other related files. -Philips can’t be held responsible for any problems that may occur as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible. Introduction This document explains how to make a Philips slideshow file with background audio. Be aware that the content of this document is addressing technical or software skilled users. To start the slideshow open the slideshow file in the Multimedia browser of your TV. 1. Press the MENU/BROWSE key on the remote control after having inserted a USB device and switched on the TV. 2. Go to where you stored the slideshow file (.alb) on your portable memory. 3. Select the slideshow file and press the OK key to start the slide show. 4. To stop a slide show, press the ‡ key. General Rules -The slideshow will use plain ASCII XML syntax to allow the creation and editing of the slideshow files using simple tools. -All references to network content must be based on the global address of the content. -Content on a Portable Memory (PM) doesn't have a global address; as a result content from a PM can never be referenced from a slideshow not stored on the PM itself. -To maintain portability, a slideshow stored on a PM should ONLY reference content on the same PM. Referencing global addresses can result in inconsistencies if the PM is used on a nonnetworked CE device. The latter is however not forbidden, it is only a recommendation. -It is preferable that URL’s referencing PM content are based on a relative path starting from the directory where the slideshow is stored. This path includes the device or drive name of the PM. An absolute path to content will also be supported. -relative path: pictures\test1.jpg, tamper.jpg, ..\new\bird.jpg, … -absolute path: USB1:\pictures1\foo_bar.jpg, C:\f1.jpg, \organization.jpg, … General Format The format and syntax below will be used to create the slideshow file (simple ascii text) with the extension .alb (.ALB). Examples: slshow1.alb, summer_holiday_2004.ALB, test.alb, … The following syntax should be used to create the text file:
Телевизоры - 37PF9731D/10 (1.6 mb)
Телевизоры - 42PF9731D/10 (1.6 mb)