Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Toshiba, модель 32A41

Производитель: Toshiba
Размер: 835.99 kb
Название файла:

Язык инструкции:en

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


2 Press s or t repeatedly until “CH PROGRAM” is displayed in purple. 3 Press T or S to start channel programming. The TV automatically cycles through all the TV or CABLE channels (depending on the mode selected), and stores the active channels in the channel memory. 4 When channel programming is done, you will see the message, “Ch Programming Completed.” 5 Press CHANNEL s or t to scan through the programmed channels. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] TIMER: 0 MINTV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] TIMER: 0 MIN TV/CABLE: TV[CABLE] CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] START[T S] CH PROGRAM CABLE 24 CH PROGRAMMING COMPLETED CABLE 16 ADD/ERASE function After using the CH PROGRAM function to automatically program channels into the channel memory, you can use the ADD/ERASE function to manually add or erase individual channels, as follows: 1 Select the channel you want to add or erase. If you are adding a channel, you must use the Channel Number buttons to select the channel. 2 Press MENU until the Setup menu is displayed on-screen. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE 3 Press s or t until ADD/ERASE is V-CHIP CONTROL FAVORITE CH displayed in purple. MOVE[t s] SELECT[T S] 4 To add the channel: TIMER: 0 MIN TV/CABLE: [TV]CABLE Press T or S until ADD is displayed in purple, indicating that the channel has been CH PROGRAM ADD/ERASE: ADD[ERASE] added to the channel memory. V-CHIP CONTROL FAVORITE CH To erase the channel: MOVE[t s] SELECT[T S] Press T or S until ERASE is displayed in purple, indicating that the channel has been erased from the channel memory. TIMER: 0 MIN TV/CABLE: [TV]CABLE CH PROGRAM ADD/ERASE: [ADD]ERASE V-CHIP CONTROL FAVORITE CH MOVE[t s] SELECT[T S] 5 Repeat steps 1–4 for other channels. 6 Press s or t to select another item in the menu, or press EXIT on the remote control to return to viewing. You have now finished programming the channel memory. CABLE channel reference chart Number on this TV Corresponding CABLE channel Number on this TV Corresponding CABLE channel 1 A-8 67 67 5 5(A-7) 68 68 6 6(A-6) 69 69 14 A .......................................... 15 B 92 92 16 C 93 93 ..........................................94 94 34 U 95 A-5 35 V 96 A-4 36 W 97 A-3 37 AA 98 A-2 38 BB 99 A-1 ..........................................100 100 60 XX 101 101 61 YY 102 102 62 ZZ .......................................... 63 AAA 123 123 64 BBB 124 124 65 65 125 125 66 66 Set up Basic Operation Advanced Operation Reference SectionPreparation The above chart is typical of many cable system channel allocations. If in doubt, consult your cable company. 17 Set upPreparationAdvanced OperationReference Section Basic Operation Set upPreparationAdvanced OperationReference Section Basic Operation Watching TV programs or videotapes CHANNEL t/s MENU TV / VIDEO VOLUME CHANNEL POWER MENU T/S t/s TV/VIDEO TV CABLE VCR MENU/ ENTER CH RTN RECALL MUTE CH CH VOL VOL 1 4 7 2 5 8 3 6 9 0 ENT100 POWER o REWPAUSESLOW FF SOURCESTILL PIP PIP CH LOCATE SWAP REC TV/VCR STOP PLAY TV/VIDEOFAV CH A EXIT RECALL Channel Number CHANNEL s/t EXIT TV/VIDEO Selecting a TV channel Select a channel in one of the following two ways: . Scan through the programmed channels in numerical sequence: – Press CHANNEL s to select the next higher channel. – Press CHANNEL t to select the next lower channel. – Continue pressing CHANNEL s or t to select the next programmed channel. . Select a channel directly: – Press the Channel Number buttons (0–9 and 100). – For example: To select channel 4, press 0—4. To select channel 38, press 3— 8. To select channel 125, press 100—2—5. If you cannot select a specific channel, make sure the TV/CABLE function is set correctly (see page 16). Selecting the video input source You can use the TV/VIDEO button to view a signal coming from other video equipment connected to your TV (such as a VCR or DVD player). See “Connecting your TV” on page 5. Note: To operate your video equipment properly, refer to the instructions provided with the video equipment. 1 Turn the TV and video equipment on. 2 Press TV/VIDEO to select VIDEO 1 or VIDEO 2. The selected source will be displayed in purple. TV VIDEO1 VIDEO2 TO SELECT PUSH TV/VIDEO 3 Operate the video equipment normally. About the DEMO (demonstration) mode When the DEMO mode is activated, your TV automatically displays a variety of its on-screen menus and special features. This function is provided for demonstration purposes only. To start the demo: 1 Press MENU until the Option menu is LANGUAGE:[ENGLISH]FRANCAIS ESPANOL displayed on-screen. DEMO: [START]STOP C.CAPT: C1 C2 C3 C4 T1 2 Press s or t until DEMO is displayed in T2 T3 T4[OFF] purple. 3 Press T or S to select START. The on- MOVE[t s] SELECT[T S] screen demo starts after about 15 seconds. To stop the demo: 1 Press EXIT or ...

Эта инструкция также подходит к моделям:
Телевизоры - 36A41 (835.99 kb)
Телевизоры - 32A41 (835.99 kb)
Телевизоры - 36A41 (835.99 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории