6 The following icons convey information about messages in the Inbox: Trash Can icon The Trash can icon denotes a message marked for deletion. To mark a message for deletion, highlight the message and press j. To unmark the message (and remove the trash can icon), press j again. To delete all messages marked with the Trash Can icon, refresh the Inbox (see item 5, above). Envelope icon The Envelope icon denotes a new, unread message. After the message is viewed, the envelope icon disappears. Chapter 8: Using the THINC™ home network feature Chapter 8: Using the THINC™ home network feature Envelope with paperclip icon The Envelope with paperclip icon denotes a new message with an attachment. Paperclip icon The Paperclip icon denotes a message with an attachment. “No Entry” icon The No Entry icon denotes a message that is too large to open. The maximum allowable message size is 300 KB. Note: If you delete an e-mail on the TV, it will also be deleted from the e-mail server identified in the account setup—even if the message indicates that it cannot be read by the TV. 7 Read, Delete From the Inbox view, you can delete messages by pressing the appropriate button (as shown in the guide at the bottom of the screen). Note: If you delete an e-mail on the TV, it will also be deleted from the e-mail server identified in the account setup—even if the message indicates that it cannot be read by the TV. 8 Exit Press O to close the Personal E-mail feature and return to the regular TV screen on the last channel viewed. Read View To read e-mail: From the E-mail Inbox window, highlight the e-mail you want to read and press T. The Read view (illustrated below) will appear. Navigate ENTER CH RTNJPEG Back Page EXIT Exit From: "tvtest2" To: "my TV" Cc: Subject: FW: Pictures Attach: xxxxxxx xxxx xxxxxxxxxxxxxxx Xxxxxxxx xxxxxx xxxx xxxxxxx xxxxxxxxx xxxx xx xxxxxxxxxxx xxxxxxxx xxxxxx xxxxxxx. Xxxxx xxxxxx xx xxxxxx xxxxxxxxx xxxxxxxxxx xxxxxx xxx xxxxxxxxx xxxxxxxxxxxxxxxx xxxxxx. Xxx xxxxx xxxxxxxxx xxxxxx 1. xxxxxxxx xx xxx x x xxxxxxxxxx xxxxxxxxxx 2. xxxxxx xxxxxx xx xxxxxxxxx xxx xxxxxxxxxx xxxxx xxx x x xxxxxx xxxx 3. xxxxx xxxxxx xxxx xxxxxxx xxxxxx xxxxxxxxxxxxxxxx (xxxxxxxx xx xxxxxxxx xxxxx xxxxx) 4. xxxxxx xxxxxx xx xxxxxx xxxxx, xxxxxxxxx 5. xxx xxxxxx xxxxxxx xxxxxx xxxxxxxxxx xxxxxxxxxxx xxx xxxxxxx 6. xxxx xxxxxxxx xxxxxxxxxxxxx xxxxxxxx xx xxxxxxx xxxxxxxxx xxxxxxxxx 7. xxxxxxx xxxxxxx xxxx xxxxxxxxxxxxx xxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxx Personal E-mail Read tvtest2 jPEG x 5 +PAGE PAGE- From the Read view, press B b to scroll up and down to view the entire message. To view a JPEG attachment using the Picture Viewer, highlight the Paperclip icon and press T. To return to the Read View from the Picture Viewer, press O. To return to the Inbox View from the Read view, press R. To close the Personal E-mail feature and return to normal TV watching on the last channel viewed, press O at any time. Chapter 9: Troubleshooting Chapter 9: Troubleshooting General troubleshooting Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions to try. Black box on-screen • The closed caption feature is set to one of the Text modes (T1, T2, T3, or T4). Set the closed caption feature to Off (-page 62). TV stops responding to controls • If the TV stops responding to the controls on the remote control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for 5 or more seconds to reset the TV. Other problems • If your TV’s problem is not addressed in this Troubleshooting section or the recommended solution has not worked, use the Reset Factory Defaults procedure (-page 49). TV will not turn on • Make sure the power cord is plugged in, and then press p. • The remote control batteries may be dead. Replace the batteries or try the control panel buttons. Picture problems General picture problems • Check the antenna/cable connections (- Chapter 2). • Press + on the remote control or TV and select a valid video input source (-page 51). If no device is connected to a particular input on the TV, no picture will display when you select that particular input source. For device connection details, see Chapter 2. • Antenna reception may be poor. Use a highly directional outdoor antenna (if applicable). • The station may have broadcast difficulties. Try another channel. • Adjust the picture qualities (-page 60). • If you are using a VCR, make sure L on the remote control is set correctly (-page 28). • Do not connect both a standard video cable and an S-video cable to the VIDEO 1 input at the same time (-page 16). Noisy picture • If you are watching an analog channel (off-air broadcast or Cable TV), you can set the CableClear®/DNR feature to AUTO to reduce visible interference in the TV picture (-page 80). Video Input Selection problems • If the Input Selection window does not appear when you press + on ...
)
