|
Фото и характеристики Sony KDF-50E2000 |
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Vertical: 59 - 61 Hz. Maximum Resolution: 1024 dots x -768 lines. Preset mode timing table for PC N. Resolution Graphic mode Horizontal Vertical (dots x lines) frequency (kHz) frequency (Hz) 1 640 x 480 VESA 60 31.469 59.940 2 800 x 600 VESA 60 37.879 60.317 3 1024 x 768 VESA 60 48.363 60.004 This TV does not support Sync on Green or Composite Sync. If a signal other than in the above chart is input, it may not be displayed properly or may not be displayed as you set. Using the Vertical frequency (Hz) of the personal computer at 60 is recommended. 37 GB Additional Information Troubleshooting Check whether the 1 (standby) indicator is flashing in red. When it is flashing The self-diagnosis function is activated. 1 Measure how long the 1 (standby) indicator flashes and stops flashing. For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. 2 Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval). When it is not flashing 1 Check the items in the tables below. 2 If the problem still persists, have your TV serviced by qualified service personnel. Picture Problem No picture (screen is dark) and no sound No picture or no menu information from equipment connected to the scarts or HDMI IN socket Double images or ghosting Cause/Remedy • Check the aerial connection. • Connect the TV to the mains, and press 1 on the TV (top side). •If the 1 (standby) indicator lights up in red, press " / 1. • Check that the optional equipment is on and press / repeatedly until the correct input symbol is displayed on the screen. • Check the connection between the optional equipment and the TV. • When connecting any equipment to the HDMI IN 6/7 socket or when changing the resolution, some dots can appear blinking on the screen for a few seconds. HDMI signal decoding is in progress and it does not indicate a malfunction. • Check aerial/cable connections. • Check the aerial location and direction. Only snow and noise appear on the screen Distorted picture (dotted lines or stripes) Picture noise when viewing a TV channel Some tiny black points and/or bright points on the screen No colour on programmes • Check if the aerial is broken or bent. • Check if the aerial has reached the end of its serviceable life (three to five years in normal use, one to two years at the seaside). • Keep the TV away from electrical noise sources such as cars, motorcycles, hair-dryers or optical equipment. • When installing optional equipment, leave some space between the optional equipment and the TV. • Make sure that the aerial is connected using the supplied coaxial cable. • Keep the aerial cable away from other connecting cables. • Select “Manual Programme Preset” in the “Set-Up” menu and adjust “AFT” (Automatic Fine Tuning) to obtain better picture reception (page 26). • The picture of a display unit is composed of pixels. Tiny black points and/or bright points (pixels) on the screen do not indicate a malfunction. • Select “Reset” in the “Picture Adjustment” menu to return to the factory settings (page 20). No colour or irregular colour when viewing a signal from Y, PB/CB, PR/CR jacks of 3 • Check the connection of the Y, CB, PR/CR jacks of 3. • Make sure that the Y, PB/CB, PR/CR jacks of 3 are firmly seated in their respective sockets. 38 GB Problem Cause/Remedy Irregular picture when viewing • Check PC input socket connection. a signal from PC • Connect to PC input socket instead of HDMI IN 6 socket. • If the connection is only available through HDMI socket, change the screen resolution to 720p and adjust horizontal and vertical screen size in the display properties settings of PC. Sound Problem Cause/Remedy No sound, but good picture •Press 2 +/– or % (Mute). • Check that “TV Speakers” is set to “On” in the “Sound Adjustment” menu (page 22). Noisy sound • See the “Picture noise” causes/remedies on page 38. Channels Problem Cause/Remedy The desired channel cannot be selected • Switch between digital and analogue mode and select the desired digital/ analogue channel. Some channels are blank • Scrambled/Subscription only channel. Subscribe to the Pay Per View service. • Channel is used only for data (no picture or sound). • Contact the broadcaster for transmission details. Digital channel is not displayed • Check that the aerial is plugged directly into the TV (not through other equipment). • Contact a local installer to find out if digital transmissions are provided in your area. • Upgrade to a higher gain aerial. General Problem Cause/Remedy The TV turns off automatically (the TV enters standby mode) • Check if the “Sleep Timer” is activated, or confirm the setting of “Off Time” (page 24). • If no signal is received and no operation is performed in the TV mode for 10 minutes, the TV automatically switches to standby mode. The TV turns on automatically • Check if the “On Time” is activa...
Эта инструкция также подходит к моделям:Телевизоры - KDF-50E2010 (5.13 mb)