Оценок - 3, средний балл: 4.3
(
)
)
|
Фото и характеристики Sony KDL-40EX725 |
К этому устройству также есть другие инструкции:
Телевизоры - KDL-40EX725 (3.41 mb)
Телевизоры - KDL-40EX725 (3.43 mb)
Телевизоры - KDL-40EX725 (28.48 mb)
Фрагмент инструкции
~ • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the TV. • When removing the Table-Top Stand from the TV, lay the display face down on a stable work surface that is larger than the TV. • To prevent damaging the surface of the LCD display, make sure to place a soft cloth on the work surface. • Be sure the TV is on the vertical position before switching on. TV set must not powered on with LCD panel face down to avoid uneven picture uniformity. 2: Adjusting the viewing angle of the TV This TV can be adjusted within the angles as illustrated. Angle adjustment (Swivel) ~ • When adjusting the angle, hold the stand with one hand to avoid having the stand slip or TV tip over. 20° 20° 20° 20° Angle adjustment (Tilt) ~ • Be careful not to pinch your fingers between the TV and stand when adjusting the angle. 0° -6° ~ • Ensure that there are no objects in front of the TV. Getting Started IR Sensor 3D Sync Transmitter • Do not expose the Presence Sensor to direct sunlight or other strong light, as malfunction may occur. Presence Sensor 9 GB 3: 3: Connecting a Set Top Box/recorder (e.g. DVD recorder) with SCART Set Top Box/recorder (e.g. DVD recorder) ~ • Right Angle Type Universal SCART Lead is recommended for this connection. • Screw the satellite connector softly with hand, do not use any tool. • TV must be switched off when connecting satellite antenna (aerial). Connecting a Set Top Box/recorder (e.g. DVD recorder) with HDMI Set Top Box/recorder (e.g. DVD recorder) Recommendation of the F type plug The one based on the following drawing is recommended about the F type plug. Projection of the inner wire from the connection part must be less than 1.5 mm. 1.5 mm max. (Reference drawing of the F type plug) 10 GB 4: 4: Audio/video device 1 Install a wood screw (4 mm in diameter, not supplied) in the TV stand. 2 Install a machine screw (M4 . 10, not supplied) into the screw hole of the TV. 3 Tie the wood screw and the machine screw with a strong cord (not supplied). Getting Started 11 GB 12 GB 6: Bundling the cables ~ • Before bundling the cables, remove the cable holder from the AC cover (see step 1 and 2). Reuse the cable holder (see step 3) to bundle the other cables (see step 4). • Do not bundle the AC power cord (mains lead) together with other cables. * When installing on the wall, attach the cable holder under the terminals. 7: Performing the initial set-up 1 Connect the TV to your AC power outlet (mains socket). 2 Press 1 on the TV. The = (power) indicator will light up in green. When you switch on the TV for the first time, the Language menu appears on the screen. ~• When you turn on the TV for the first time, the TV requires some internal processing for optimization before you can perform the initial setup. There will be no picture and sound, and the timer indicator on the front of the TV blinks orange for about 40 seconds. Do not turn off the TV during this process. This process has been completed at the factory for some TVs. Follow the instructions on the screen. * 3 4 1 2 3 Satellite Auto Tuning: Satellite Auto Tuning: 1 Please select “Preferred Satellite” or “General Satellite”. 2 For “Preferred Satellite”, select your preferred operator. “Satellite Auto Tuning” automatically tunes in available satellite channels. Digital Satellite Equipment Control (DiSEqC) 1.0 management allows setting of up to four different channels. The following settings are independent for each connection. To set-up DiSEqC input in the “DiSEqC Control”, use “LNB Configuration”. 1 “Scan Type” and “Advanced Settings” (for common satellite setting- Satellite 1 to 4): Allows you to set tuning settings in more detail to better find the type of services you would prefer to tune. “Scan Type”: If no channel is found using “Network Scan”, try “Full Scan”. “Full Scan”: Performs a complete frequency scan and guarantees tuning to all possible programmes for the currently set LNB configuration. Previously-tuned programmes will be lost. “Network Scan”: Performs a scan in the transponders of a network (aka NIT scan). Since “Network Scan” is faster than “Full Scan”, it is recommended when tuning to a known network (normally associated with a satellite). A transponder must be specified, from which network information (other transponders) will be retrieved. Previously-tuned programmes will be lost. 2 “LNB Configuration” (for each satellite setting- Satellite 1 to 4): In the case of a non-standard LNB (lownoise block), manual setting is available. – In the case of a single satellite channel, you can leave it on the initial setting. – For two satellite channels, you need to set “Toneburst A” (1st satellite) and “Toneburst B” (2nd satellite) in the “DiSEqC Control” setting. – Or you can use DiSEqC command A (1st satellite) and B (2nd satellite), if your LNB or multi switch can handle these commands. – For four satellite channels, DiSEqC control A, B, C, and D is required. “LNB Low Band Frequency” and “...