Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
. as long as the power cord is inserted and PC input signal modes sequentially. into the wall outlet.) (see page 19) .....Red • STAND-BY • POWER-ON.....Green INPUT button (VIDEO (S VIDEO), COMPONENT/ RGB and PC Mode Selection) Press to select VIDEO (S VIDEO), COMPONENT/RGB and PC input signal modes sequentially. (see page 19) Sound mute On/Off (see page 26) VOLUME Adjustment Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level. R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT button Press to adjust the aspect. (see page 22) OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. The directly to PC mode. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. When three minutes remain, “Off timer 3” will flash. The off timer is cancelled if a power interruption occurs. PC button Press the “PC” mode selection button to select the PC mode. INPUT SURROUND VOL N R PICTURE SOUND SET UP ASPECT PICTURE POS. /SIZE OFF TIMERPC STAND-BY (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 18). Press this button to turn the Plasma Display ON, from STANDBY mode. Press it again to turn the Plasma Display OFF to STAND-BY mode. SURROUND button (see page 27) N button (see page 25, 26, 28, 29) PICTURE button (see page 28) PICTURE POS./SIZE button (see page 24) STATUS button Press the “STATUS” button to display the current system status. 1 VIDEO (S VIDEO), COMPONENT/RGB, PC mode 2 ASPECT mode (see page 22) 3 OFF TIMER The OFF TIMER indicator is displayed only when the off timer has been set. OFF TIMER 90 1 2 3 VIDEO NORMAL 30 60 0 90 Connections SPEAKER Terminals (R) To tighten: To loosen: Push the catch Pull Pull 1 2 – Cable fixing bands Secure any excess cables with bands, as required. SPEAKER Terminals (L) Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. PR/CR/R PB/CB/B Y/G COMPONENT/RGB INAV VD HD R L S VIDEO IN VIDEO IN AUDIO IN R L AUDIO AUDIO VIDEO OUT PC IN SERIAL From EXIT monitor Terminal on Computer (see page 15) COMPONENT/RGB IN and Audio IN Terminals (see page 14) AV Terminals (see page 12, 13) From SERIAL Terminal on Computer (see page 17) Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. 1 1 2 2 Refer to the speaker’s Installation Manual for details on speaker installation. Speakers (Optional accessories) AV Input Terminals connection Connect the signal source equipment (see page 14 to 17). (Example) When connecting an S VIDEO VCR (S VIDEO VCR) 2.RCA audio cables Luminance earth Luminance in Chrominance earth Chrominance in S VIDEO 4 pin socket AUDIO S VIDEO Audio input to L/R sockets Audio Video S VIDEO OUT OUT OUT RL R L AUDIO IN S VIDEO IN VIDEO IN AV VIDEO OUT Video input to S VIDEO socket Note: Additional equipment and cables shown are not supplied with this set. Connections AV Input connection VIDEO signal connection S VIDEO IN VIDEO OUT Audio OUT Video OUTR L VIDEO RCA-BNC video cable Video input to BNC socket Audio input to L/R sockets AUDIO 2.RCA audio cables VIDEO RCA video cable Audio OUT Video OUTR L Video input to BNC socket RCA-BNC adapter plug Audio input to L/R sockets AUDIO 2.RCA audio cables (VCR) (VCR) AV R L AUDIO IN VIDEO IN Note: Additional equipment and cables shown are not supplied with this set. VIDEO OUT S VIDEO IN AV R L AUDIO IN VIDEO IN VIDEO OUT MONITOR DEVICE BNC cable (Example) color CRT monitor Connections COMPONENT/RGB Input connection Component signals (Y, PB, PR) connection RCA-BNC (DVD Player) adaptor plug (1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “COMPONENT”. (see page 34) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. AUDIO 3.RCA video cables 2.RCA audio cables Y, PB, PR PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN VD HD R L AUDIO Y PB PR L R Notes: RGB signal (R, G, B, HD, VD) connection G RCA-BNC adaptor-plug Example of input signal source HDTV-compatible VCR Computer RGB camera R L AUDIO VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN Notes: (1) Change the “COMPONENT/RGB-IN” setting in the “SET UP” menu to “RGB”. (see page 34) (2) Additional equipment, cables and adaptor plugs shown are not supplied with this set. Connections PC Input Terminals connection COMPUTER AUDIO Conversion adapter (if necessary) RGB D-sub 15p Stereo plug PC cable Connect a cable that matches the audio output terminal on the computer. POWER / R - STANDBY G POWER ON INPUT – VO L + Less than 3" 15/16 (10 cm) Audio Less than 3" 15/16 (10 cm) Ferrite core (small size) (supplie...
Эта инструкция также подходит к моделям:Телевизоры - TH-42PHD5 (796.19 kb)