Оценок - 3, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
INPUT lock Off PC INPUT1 INPUT2 INPUT3 Locks the input switch operation. Notes: • Only the adjusted signal is displayed (see page 18). • Signal can be displayed when the Terminal board is installed. • Input switch can be used when this is set to “Off”. • In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input in the single screen display mode. Studio W/B Off On Off: Nullify all the settings adjusted. On: Sets the color temperature for TV studio. Note: Valid only when the low is set as color temperature on screen adjustment. Advanced PIP Off On Off: Sets normal two screen display mode (see page 21). On: Sets Advanced PIP mode (see page 22). Notes: • When “INPUT lock” is “On”, you cannot use all the two screen display functions. • , buttons are unavailable during Advanced PIP mode operation. Adjusts the image display size on screen. Off: Sets the normal image display size on screen. On: Sets the image display size approximately 95 % of the normal image display. Off On Display size Off On Notes: • This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI) • This setting is invalid when two screen display, digital zoom or Multi screen is selected. • When Display size is set to “On”, Pos. /Size adjustment cannot be used. • Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals. Options Adjustments 2/3Options Off Off Off Off 0 Remote ID Serial ID ID select Button lock Remocon User level Item Effect Adjustments Button lock Off MENU&ENTER On Off: All the buttons at the bottom of the main unit can be used. MENU & ENTER: Locks MENU and ENTER/ buttons on bottom face of main unit. On: Locks all the button on bottom face of main unit. Remocon User level Off User1 User2 User3 Off: You can use all of the buttons on the remote control. User1:You can only use , , , , , , , buttons on the remote control. User2:You can only use , , buttons on the remote control. User3:Locks all the buttons on remote control. ID select Sets panel ID number when panel is used in “Remote ID” or “Serial ID”. Set value range: 0 - 100 (Standard value: 0) Remote ID Off On Off: Disables ID remote control functions. You can use normal remote control operations. On: Enable ID remote control functions. Serial ID Off On Sets the panel ID Control. Off: Disables external control by the ID. On: Enables the external control by the ID. 3/3Options Off Off Off V. lnstallation Rotate Slot1Serial Slot Select Slot power Item Effect Adjustments Slot Power Off Auto On Off: Power is not transmitted to the slot power. Auto: Power is transmitted to the slot power only when main power is on. On: Power is transmitted to the slot power when main power is on or in the standby state. Note: In some cases, power is transmitted to the slot power when main power is on or in the standby state regardless of the slot power setting. V.Installation Off On Off: Sets fan to the horizontal installation mode. On: Sets fan to the vertical installation mode. Notes: • This functions when display is turned on. • This mode is available for TH-42PH9UK, TH-50PH9UK. • Vertical installation is available for TH-42PS9UK without this mode setting. • Turn up the power switch for the upward direction when you set Display vertically. Rotate Off On Off: Does not rotate the image. On: Rotates the image 180 degrees. Serial Slot Select Slot1 Slot2 Slot3 Selects the slot which communicates serial. Note: The setting of an external command can be set only from the fixed serial terminal (see page 11) Normalization When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote ID” adjustments, set all the values “Off” so that all the buttons are enabled again. Press the button on main unit together with button on the remote control and hold for more than 5 seconds. The “SHIPPING” menu is displayed and the lock is released when it disappears. Shipping condition This function allows you to reset the unit to the factory setting. 1 2 2 Press to display the SET UP menu. Press to select “OSD LANGUAGE”. Press and hold till the SHIPPING menu is 3 displayed. Press to select “YES”. 4 SHIPPING YES Press to confirm. [from the unit] 1 Press the MENU button till the Setup menu is displayed. 2 Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”. 3 Press and hold the ENTER button till the SHIPPING menu is displayed. 4 Press the Volume Up “+” or Down “–” button to select “YES”. 5 Press the ENTER button. Note: Press the R button to return to SET UP menu when SHIPPING menu is displayed. 1/2PC OFF STANDBYSAVE OFF POWER MANAGEMENT OFF AUTO POWER OFF OFF OSD LANGUAGE ENGLISH (US) COMPONENT/RGB-IN SELECT RGB INPUT LABEL SIGNAL POWER SAVE SET UP Troubleshooting Before you call for service, determine the symptoms and make a few...
Эта инструкция также подходит к моделям:Телевизоры - TH-37PH9UK (2.76 mb)
Телевизоры - TH-42PH9UK (2.76 mb)
Телевизоры - TH-50PH9UK (2.76 mb)