2 OK Press to select menu and sub-menu items. 3 TV/VIDEO Changes Input source. 4 VOL -+ / ....Press to adjust TV sound and navigate in menus. 5 CH > ....Press to change channels and navigate in menus. 1 TEMP indicator Lights up when temperature inside unit is abnormal. (P. 65) 2 Remote Control Sensor Receives infrared signal from Remote Control. 3 LAMP indicator Lights up when the lamp unit is malfunctioning. (P. 65) 4 S-Video Input Connector 3 Connect from other component. (Video 3) 5 Video Input Connector 3 Connect from other component. (Video 3) 6 Audio Input Connector (Shared with both Video 3 and PC) Connect from other component. (Video 3) Connect from PC. (PC) 7 PC (RGB) Input Connector Connect from PC. (PC) 8 SD CARD Slot Insert SD Card. 1 2 3 4 5 1 2 3 4 5 6 8 POWER button / POWER indicator Remote Control Sensor Note: • Buttons listed above operate the same as remote control buttons of the same name. 7 OpenUsing your finger, slide Cover in direction of arrow to open. Cover 11 Getting Start ed Vent Notes: • Make sure the vents are not blocked. (This could cause damage.) • Indication on the back panel may change without notice. Vent 1 CableCARD™ INTERFACE Insert CableCARD™. 2 VHF/UHF Cable In Input terminal for an antenna or cable box signal. 3 DIGITAL AUDIO OUT Output audio signal (Digital) 4 HDMI Input Terminal 1 Audio/ Video 1 Connect from other component. (HDMI 1) 5 Audio 1 Connect from other component. (HDMI 1) (P.22) 6 HDMI Input Terminal 2 Audio/ Video 2 Connect from other component. (HDMI 2) 7 Audio 2 Connect from other component. (HDMI 2) (P.22) 8 S-Video/Video Input Connector 1 Connect from other component. (Video 1) 9 Audio Input Connector 1 Connect from other component. (Video 1) 1 2 3 4 7 8 10 14 16 18 9 11 15 17 19 10 S-Video/Video Input Connector 2 Connect from other component. (Video 2) 11 Audio Input Connector 2 Connect from other component. (Video 2) 12 Video Out Connector Output video signal 13 Audio Out Connector Output audio signal (Analog) 14 Component Video Input Connector 1 Connect from other component. (Component 1) 15 Audio Input Connector 1 Connect from other component. (Component 1) 16 Component Video Input Connector 2 Connect from other component. (Component 2) 17 Audio Input Connector 2 Connect from other component. (Component 2) 18 Component Video Input Connector 3 Connect from other component. (Component 3) 19 Audio Input Connector 3 Connect from other component. (Component 3) 12 13 Rear View 5 6 12 For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: Antenna Connection VHF/UHF Cable In terminal on the back of the Projection Display Connecting the Antenna / Cable to the RF IN Terminal When using “Nut type” RF coaxial cable, tighten with fingers only. Overtightening may damage terminal. • Turn off the power supply for all com ponents before making any connections. • If the cables necessary for connecting a component to the system are not included with the component or available as an option, you may need to fashion a cable to suit the component concerned. • Read the instruction manual for each system component care fully before connecting it. • If there is a lot of jitter in the video signal input from the video source, the picture on the screen may flicker. In this case, it will be necessary to connect a TBC (time base corrector). Notes on con nections Mixer Installation For proper reception of digital and analog VHF/UHF channels, an external antenna is required. For best reception, an outdoor antenna is recommended. VHF Antenna UHF Antenna RF Coaxial Cable CAUTION 13 Getting Start ed For proper reception of analog or digital cable channels, a cable service connection is required. Cable Connection Cable Box Terminal on the back of the Cable Box In from cable Connect the cable from the antenna or cable system to the VHF/UHF Cable In terminal on the back of the Projection Display. Or In from cable Use this confi guration when connecting the projection display to a cable TV system. Notes: • Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable converter box is required for proper reception. Check with your local cable company for its compatibility requirements. • For reception of cable channels, connect the cable supplied by your local cable company. 14 For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: CableCARD™ Connection This module (also called Point of Deployment (POD) module or Digital Cable Module (DCM)) allows you to tune digital and high definition cable channels through the cable antenna. Contact your local cable company for information regarding the availability and costs of CableCARD™ related services. Notes: • A Digital Cable Subscription is required. • Do not insert a PC card into the CableCARD™ INTERFACE. • Follow the instruction...