Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
1 024 X 768 60.24 74.93 MAC 19 * XGA (85 Hz) 1 024 X 768 68.68 85.00 XGA 85Hz DTV FormatSignals 480 i 664 X 485 15.73 29.97 480 i 480 p 720 X 483 31.47 59.94 480 p 720 p 1 280 X 720 45.00 60.00 720 p *1080 i 1 920 X 1 080 33.75 30.00 1080 i Notes: • Input signals, other than those listed with a * mark, will give you a beautiful, stable picture. • The front D-SUB15P connector can accept RGB(H-V sync separate) and RGB(sync on green). However, it is not guaranteed to display stable color when using RGB(sync on green). • When used with an external video processor/scaler, it must have RGB(H-V sync separate) output. Getting Started 19 Power ON and OFF Initial Setup First, check the connection of the Plug to the Wall Outlet and the Antenna/Cable to the RF in Terminal. (PP. 12-14.) If using Cable Box, DSS Receiver, or VCR, • Turn on Cable Box. • Turn off DSS Receiver, or VCR. 1 Press the POWER button to turn the projection display on. (Refer to page 21 for “Turning the Power ON and OFF”.) Automatic Channel Setting is performed. CH AUTO SET PROCEED ING Note: To cancel AUTO SET in progress, press the SWAP button. Case 1When setup is complete, the lowest channel picture appears. Case 2 If setup is incomplete, the following screen appears. Check connection of Antenna/Cable to the RF in Terminal, then try Automatic Channel Setting again. (PP. 24, 25) NO CH FOUND PLEASE CHECK ANTENNA CABLE CONNECT ION THEN PRESS ACT ION KEY AGAIN Note: When the unit is turned on for the first time, Automatic Channel Setting is performed. For assistance, please call : 1-888-VIEW PTV(843-9788) Power ON / OFF Turning the Power ON and OFF Always be sure to follow the procedure given below to turn the projection display power ON and OFF. • The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the POWER indicator will blink Red. Do not disconnect the power cord from the power outlet and do not open any circuit breakers while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the power indicator blinks Red. POWER button/ POWER indicator Power ON Press the POWER button on the projection display or the remote control to turn the power on. The Power Indicator will become Green and blink for approximately 10 seconds, and then turn solid Green. Power OFF Press the POWER button on the projection display or the remote control to turn the power off. Confirming message will appear. POWE. OF. Press the POWER button again. YE. N. If the POWER button is accidentally pressed, select NO with the , buttons, then press the ACTION button. The Power Indicator will become Red and blink for approximately 1 minute, and then turn solid Red. Note: When the AC Cord is unplugged, the internal cooling fan stops operating. In this case, the lamp will be insufficiently cooled and will take a while to turn ON again. The Power Indicator LED ACTION Red Power – OFF (Standby mode) Red blink Power – OFF (Now cooling) Green Power – ON Green blink Power – ON (Preparing to light lamp) Basic Operation Notes: • If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the lamp automatically comes on. • After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal. 21 Flow Chart of Main menu 2 PUTESPAGESELECTENDRECALLTSUJDAPUTESERUTCIPOIDUAEZIS/NOITISOPNOITAMROFNIPAGESELECTENDRECALLTSUJDAPUTESERUTCIPOIDUAEZIS/NOITISOPNOITAMROFNIPAGESELECTENDRECALLPUTESHSILGNE:EGAUGNALLENNAHCKCOLNOITPACOEDIV Use the , buttons to select an item. Select MENU desired by pushing Left “ ” button or Right “ ” button. Use the ACTION button to set or go to next menu screen. Pressing the ACTION button displays the MENU screen. Note: Depending on the signal being input, some items may or may not be adjustable and some functions may or may not be available. 1 Flow Chart of Main menu 2 PUTESPAGESELECTENDRECALLTSUJDAPUTESERUTCIPOIDUAEZIS/NOITISOPNOITAMROFNIPAGESELECTENDRECALLTSUJDAPUTESERUTCIPOIDUAEZIS/NOITISOPNOITAMROFNIPAGESELECTENDRECALLPUTESHSILGNE:EGAUGNALLENNAHCKCOLNOITPACOEDIV Use the , buttons to select an item. Select MENU desired by pushing Left “ ” button or Right “ ” button. Use the ACTION button to set or go to next menu screen. Pressing the ACTION button displays the MENU screen. Note: Depending on the signal being input, some items may or may not be adjustable and some functions may or may not be available. 1 For assistance, please call : 1-888-VIEW PTV(843-9788) Flow Chart of Main menu Returning to the previous screen If you press the RECALL button while a menu screen is being displayed, the display will return to the previous screen. Adjust items Set an item EXITRECALLi084LANGISTUPNI INFORMATION screen P. 57 SELECTEXITRECALLNOITISOPHNOITISOPNOITISOPVWORRAN:HTDIWHLAMRONADJUST TO POSITION/SIZE ADJUST menu PP. 40, 41 SELECTEXITRECALLOIDUALAMRON:UNEMOIDUATSUJDAOIDUANO:REKAEPSFFO:DNU...
Эта инструкция также подходит к моделям:Телевизоры - PT45LC12 (4.19 mb)
Телевизоры - PT 45LC12 (4.19 mb)
Телевизоры - PT 40LC12 (4.19 mb)