Войти:
Оценок - 1, средний балл: 5 ( )

Инструкция по эксплуатации Panasonic, модель CT2521HD

Производитель: Panasonic
Размер: 1.8 mb
Название файла:
Язык инструкции:enes
Перейти к скачиванию



Фрагмент инструкции


– 13 – • The red LED will flash while the data is uploaded into the box. The green LED will light for about two (2) seconds when the procedure is complete. • If the green LED does not light for about two (2) seconds, retry by holding the ALT button while pressing the LEARN button. 7. Disconnect the clone box from the television and turn it OFF. 8. Reset the volume on the television. 9. Refer to the section entitled Setting Up Other Televisions Using the Clone Box (TEACH). Testing the Settings in the Clone Box This test compares the clone box settings with the television settings. The television must be in Commercial (Hotel) mode. 1. Press the POWER ON button on the clone box. • The LEDs will flash red and green to confirm power is ON. 2. Connect the clone box to the Digital Interface port on the back of the television. • The television must be plugged into an AC outlet but can be either OFF or ON. 3. Press the TEST button. • The LEDs will flash red and green while the data is compared. The green LED will light for about two (2) seconds if the settings in the box match the television. 4. Disconnect the clone box from the television and turn it OFF. Testing the Clone Box Battery 1. Press the POWER ON button on the clone box. • The LEDs will flash red and green to confirm power is ON. 2. Hold the ALT button while pressing the TEST button. • The LEDs will alternately flash red and green while the box is tested. Note: Replace the 9 volt battery if the LEDs do not flash red and green. • The green LED will light for about two (2) seconds, if battery is charged. Note: If the green LED does not light for about two (2) seconds at the end of the test, new datamust be downloaded into the box. • El indicador rojo emitira una luz intermitente mientras la informacion es grabada en la caja de clonacion. El indicador verde emitira una luz continua por aproximadamente dos segundos cuando el procedimiento halla concluido. • Si el indicador verde no emite luz por los aproximados dos segundos, vuelva a intentar presionando el boton ALT y LEARN simultaneamente. 7. Desconecte la caja de clonacion del la television y APAGUELA. 8. Reajuste el volumen en la television. 9. Refierase a la seccion titulada Configurando otras televisiones usando su caja de clonacion (ENSENA). Probando la configuracion en la caja de clonacion. Mediante este procedimiento se compara la configuracion de la caja de clonacion con la de la television. La television debe estar en la modalidad comercial (hotel). 1. Presione el boton POWER ON en la caja de clonacion. • Los indicadores rojo y verde emitiran una luz intermitente para confirmar que la caja de clonacion esta encendida. 2. Conecte la caja de clonacion a la interface digital en la parte posterior de la television. • Aunque la television puede estar encendida o apagada debe estar conectada al suministro de corriente alterna. 3. Presione el boton TEST (Prueba). • Los indicadores rojo y verde emitiran una luz intermitente mientras se compara l...

Эта инструкция также подходит к моделям:
Телевизоры - CT2511HD (1.8 mb)
Телевизоры - CT2721HD (1.8 mb)
Телевизоры - CT3221HD (1.8 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории