Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
If the EDID mode has been changed it will not take effect until the unit has been reset. 2 Activity Indicator This LED indicator will turn bright blue when an input signal is detected. 3 Power Indicator This LED indicator will become active once the included 5V DC power adapter has been properly connected. 4 EDID Selection Switch Switches between the built-in Internal EDID and External (Pass-Through) EDID. 5 HDMI Input Port Connect an HDMI or DVI (with a DVI to HDMI adaptor or cable) source device to this input port. 6 HDMI Output Ports 1 - 10 Connect up to 10 HDMI or DVI (with a HDMI to DVI adapter or cable) displays to these output ports. The display connected to the port labeled OUT 1 will have its EDID used when the external mode is active. 7 24V DC Power Input Connect the included 24V DC power supply to this port. 5 CONNECTING AND OPERATING THE 1:10 SPLITTER FOR HDMI 1.3 How to Connect the 1:10 Splitter For HDMI 1.3 1. Connect the HDMI or DVI (with a DVI to HDMI adapter or cable) source device to the 1:10 Splitter For HDMI 1.3 HDMI input port using the supplied HDMI cable. 2. Connect up to ten HDMI or DVI (with a HDMI to DVI adapter or cable) displays to the 1:10 Splitter For HDMI 1.3 output ports using user supplied HDMI cables. 3. Connect the included 5V DC power adapter to the 1:10 Splitter For HDMI 1.3 power input port. 4. Power on the displays first and then the source. Wiring Diagram for the Gefen 1:10 Splitter for HDMI 1.3 EXT-HDMI1.3-1410-SIL HDMI Source HDMI Splitter HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI Display HDMI CABLE 6 EDID MANAGEMENT EDID Mode Selection 1. EXTERNAL MODE: To use this mode, move the EDID switch to the Ext position. See page 8 for details on using the External EDID. 2. INTERNAL MODE: To use this mode, move the EDID switch to the Int position. This mode will use a preset EDID, from the factory, that is stored in the Gefen 1:10 Splitter For HDMI 1.3. This pre-programmed standard EDID data structure is compatible with most A/V display devices. All resolutions and audio formats specified in this EDID will be passed to the source device. See the tables below for a complete listing of the resolutions and audio formats listed in this EDID. NOTE: All other HDMI devices/displays connected to the output ports must be compatible with at least one resolution/audio format specified in this EDID. It is recommended to set, on the source device, a common resolution and audio format shared by all attached devices/displays. This is to ensure a compatible signal is output to all connected devices/displays. Internal EDID Video Timings Timing Refresh Rate Timing Refresh Rate 1280 x 720p 50 Hz 720 x 576p 50 Hz 1280 x 720p 59.94 / 60 Hz 1920 x 1080p 50 Hz 1920 x 1080i 50 Hz 1920 x 1080p 59.94 / 60 Hz 1920 x 1080i* 59.94 / 60 Hz 1440 x 480p 59.94 / 60 Hz 720 x 480p 59.94 / 60 Hz 1440 x 576p 50 Hz * Native Resolution Internal EDID Audio Formats Audio Format Supported Channels LPCM 2CH AC-3 2CH / 5.1CH DTS 2CH / 5.1CH 7 EDID MANAGEMENT External EDID Management The 1:10 Splitter For HDMI 1.3 features EDID Management. Before the source can send video or audio signals, the source device reads the EDID (Extended Display Identification Data) from the output devices connected to the Splitter. The EDID contains information about what type of A/V data that the source can send to each output device. The 1:10 Splitter For HDMI 1.3 distributes a single source to multiple output devices. This involves reading EDID data from more than one device. Management of the EDID data is important to maintain compatibility between all devices. The following EDID features are copied from Output 1: • Supported Resolutions • 3D Support • Audio Features EDID color features are built based on all attached displays, using the following rules: • Deep Color will be enabled if one or more displays that are connected to the Splitter support Deep Color. • xvYCC (x.v.Color) is disabled if one of more displays do not support xvYCC. Display Connections: • If a display is not connected to Output 1, then no EDID changes are made, meaning that the previous EDID information will be used. This state will be in effect until a display is connected to Output 1 and the Splitter is power- cycled. • EDID is built from Output 1 to the Input. The audio block will be copied from Output 1. EDID-copying is performed only when the Splitter is reset or power-cycled. 8 SPECIFICATIONS Video Amplifier Bandwidth ....................................................................... 225 MHz Input Video Signal .............................................................................. 1.2 Volts p-p Input DDC Signal ......................................................................... 5 Volts p-p (TTL) Supported Resolutions ....................................................... 1080p, 1920x1200, 2K HDMI Connector ...........................................................
Эта инструкция также подходит к моделям:Телевизоры - EXT-HDMI1.3-1410-BLK (195.11 kb)