Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Check that the set will not hamper operation of the shift stick before choosing the place of installation.(Figure 2) Dashboard 6. The main unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. (Figure 5) TN T NN T Figure 5 Shift stick 182 mm 53 mmInstrument panel Rear fastening hole (of vehicle) HoleHole 2–Springs Outer escutcheon Special screw Rubber cap Stoppers Stoppers Screwdriver Universal mounting bracket Main Unit Note: Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the main unit. Shift stick (check that it does not touch the LCD) Figure 2 3. Install the unit within 30° of the horizontal plane. (Figure 3) Max. 30° Figure 3 4. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 5. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 4) Chassis Chassis Max. 8 mm Damage Figure 4 Figure 6 TB731P/TB732P/TB733W TB731P/TB732P/TB733W 22 23 TB731P/TB732P/TB733W 25 English Installation and Wire connection manual 24 TB731P/TB732P/TB733W English Installation and Wire connection manual Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (*) (Figure 8). If the vehicle is not equipped with a factoryinstalled radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws at both sides of the main unit and slide the springs to the direction of arrow and remove them (Figure 7). 2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models. 3. Wire as shown in Section 7. 4. Secure the unit in the dashboard, and then reassemble the dashboard and the center panel. *: The parts and screws with this mark are used to install radio or included in the installation kit. The parts and screws with this mark are originally attached to the vehicle. : Center Panel (Note 1) Main Unit Mounting bracket (1 pair for the left and right sides) Dashboard Pocket 4–Hexagonal screws * (M5 . 8) Main Unit 2–Springs Figure 7 Figure 8 2–Screws Screwdriver Note 2 Note 1: In some cases, the center panel may require some modification (trimming, filling, etc.). Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. 6. REMOVING THE MAIN UNIT 7. CAUTIONS ON WIRING 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, then pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) Note: Keep the hook plate. You cannot remove the main unit without disengaging the hook plate. 2–Hook plates Spring Universal mounting bracket Instrument panel Figure 9 A Outer escutcheon B Main Unit 1. Be sure to turn the power off before wiring. 2. Be particularly careful where you route the wires. Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires. 3. When connecting the ground lead, fasten the ground lead (black) securely to a clean metal plate on the car. (Figure 10) If the set is insufficiently grounded, it may not operate or there may be noise. 4. If the fuse should blow, check to see if the wiring is correct. If it is, replace the fuse with a new one with the same amperage rating as the original. 5. To replace the fuse, remove the old fuse of the power supply lead and insert the new one (3A). (Figure 11) After the connection, fix the lead by a clamp or insulation tape for protection. CAUTION Screw on car Fasten securely to a clean metal plate on the car. Figure 10 Fuse Fuse holder Figure 11 ¦ RCA Extennsion Cable 8. WIRE CONNECTIONS • Do not remove the insulating cap of the RCA extension cable which is not going to be Yellow connected to prevent it from short-circuit. • Fix the RCA extension cable with insulating tape so that the connection part is not going to be loose. Insulating tape (left) Installation and WireEnglish connection manual English Installation and Wireconnection manual System expansion terminal Gray Gray White Red Audio output Audio output Gray Black Yellow White Red Video output Video input Audio input (left) Audio input (right) Black Black output terminal (.1) TV antenna terminal (MINI o3.5) (.7) Main antenna input terminal Ground lead (.5) Main power supply lead (.4) Accessory power supply lead (.3) Illumination power supply lead Parking brake lead (.6) (.8) Black Yellow Red Orange/white Bright green Brown (right) ¦ Conce...
Эта инструкция также подходит к моделям:Телевизоры - TB731P (507.21 kb)
Телевизоры - TB733W (507.21 kb)