Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components. Also make sure the cables are the correct length. 300-Ohm Twin Lead Connector This outdoor antenna cable must be connected to an antenna adaptor (300-Ohm to 75-Ohm). Phono Connector Used on all standard video and audio cables which connect to inputs and outputs located on the Television's rear jack panels. "F" Type 75-Ohm Coaxial Antenna Connector For connecting RF signals (antenna or cable TV) to the antenna jack on the television. S-Video (Super Video) Connector This connector is used on camcorders, VCRs, and laser disc players with an S-Video feature in place of the standard video cable to produce a high-quality picture. ANTENNA CONNECTIONS TO REAR JACK PANEL VHF (75-Ohm) antenna/CATV(cable TV) When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV coaxial cable to the VHF/UHF 75-Ohm terminal. VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna FRONT PANEL CONTROLS - 12 - leads to screws of the VHF or UHF adaptor. Plug the adaptor into the antenna terminal on the TV. When both VHF and UHF antennas are connected Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer. FRONT PANEL CONTROLS Click to see front panel diagram. . MENU BUTTON Thjis button allows you to enter the MENU mode without using the remote. This makes it possible to set TV features to you preference, without using the remote. . AVX (Audio/Video) selector/ ENTER button Press this button to select the current antenna source, VIDEO: 1 or VIDEO: 2. Your selection is shown in the top right corner of the screen. This button also serves as the ENTER button when in MENU mode. . VOLUME level Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left and right buttons when in MENU mode. . CHANNEL selector Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down and up buttons when in MENU mode. . POWER button Press this button to turn TV on or off. . POWER light You will see a red light when the TV is turned on. REAR PANEL JACKS -13 NOTE: Your HITACHI TV will appear to be turned "off" if there is no video input when VIDEO: 1 or VIDEO: 2 is selected. Check the POWER Light to make sure the TV is off when not in use. . AI (Artificial Intelligence) sensor This "Artificial Intelligence" sensor will make automatic picture adjustments depending on the amount of light in the room to give the best picture. (See page 34) . REMOTE CONTROL sensor Point your Remote at this area when selecting channels, adjusting volume, etc. REAR PANEL JACKS Click to see Rear Panel Jacks. . Antenna Input Use an "F" type coaxial cable to connect an antenna or cable TV (CATV) output to this rear panel jack. . Audio/Video Inputs 1, 2 The "AVX" (Auxiliary video) button will step through each video source and the current antenna input each time it is pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laser disc players, etc. (If you have mono sound, insert the audio cable into the left channel jack.) . Monitor Out These jacks provide fixed audio and video signals which are used for recording. . Audio to Hi-Fi These jacks provide variable audio output to a separate stereo system amplifier. With this connection, the audio to the stereo can be controlled by the television's remote control. . Speaker Matrix Surround Switch Use this switch to choose between the surround and external speaker features. See page 13 for Audio System setup. The TV's Internal Speakers will be switched off when "EXT." is selected. . Rear Speaker Terminals These terminals are used to connect external speakers, which are used for the surround sound feature. The volume level is controlled by the remote control main volume buttons. Use speakers with 8 Ohm impedance only. . S-Video Input 1 provides S-Video (Super Video) jacks for connecting equipment with S-Video output capability. REAR PANEL CONNECTIONS - 14 REAR PANEL CONNECTIONS Typical full-feature set-up. Follow connections that pertain to your personal entertainment system. REAR SPEAKER TERMINAL CONNECTIONS CONNECT AFTER TURNING THE POWER TO THE TV OFF. Press the Right Speaker red button and insert the positive (+) lead wire into the hole below the button. When the button is released, the wire is locked into place. In the same manner, press the Right Speaker black button and insert the negative (-) lead wire. Repeat this procedure for the Left Speaker. CAUTION: Do not short speaker terminals, ...
Эта инструкция также подходит к моделям:Телевизоры - 50EX12BX (1.33 mb)
Телевизоры - 50EX16B (1.33 mb)