Войти:
Оценок - 4, средний балл: 4.3 ( )

Инструкция по эксплуатации Hitachi, модель WD-62628

Производитель: Hitachi
Размер: 6.36 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections COMPONENTYPbPr (480i/480p/720p/1080i)INPUT12S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTDTV/CABLE/ VHF/UHFANT 1 / MAINANT 2 / AUXDIGITALAUDIOOUTPUTCableCARD™ USE WITH ANT 1 CARD TOP12YPbPrAUDIO- LEFT/ (MONO) AUDIO- RIGHTOUTPUTAUDIOOUTPUTRECORDOUTPUTDVIAnalog Audio12VIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTMONITORLINK™/HDMIVIDEO 480i/480p/720p/1080iAUDIO PCM LINEAR12IEEE 1394 INPUT/ OUTPUTNet CommandIR EMITTER .................. INPUTPC - 60HzVGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720 ........................................................................................................................................................................................................ Figure 8. Connecting a Satellite Receiver with S-Video Note: NetCommand® assumes you connected your satellite receiver to Input-2. If you add a second satellite receiver or use any other inputs for your satellite receiver, this change must match in the NetCommand system. See Editing NetCommand Setup in Chapter 3 for more information. Connecting a DVD Player with Component Video Connecting a DVI Device DVD Player with Component Video Figure 9 Component video cables and audio cables are required. These are not included with the TV. 1. Connect the Component Video cables from Y/Pr/ Pb VIDEO OUT on the back of the DVD player to COMPONENT-2 on the TV back panel, matching the correct connection: • Y to Y (Green) • Pr to Pr (Red) • Pb to Pb (Blue) 2. Connect a set of audio cables from AUDIO OUT on the back of the DVD player to COMPONENT-2 AUDIO Input on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel. COMPONENTYPbPr (480i/480p/720p/1080i)INPUT12S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTDTV/CABLE/ VHF/UHFANT 1 / MAINANT 2 / AUXDIGITALAUDIOOUTPUTCableCARD™ USE WITH ANT 1 CARD TOP12YPbPrAUDIO- LEFT/ (MONO) AUDIO- RIGHTOUTPUTAUDIOOUTPUTRECORDOUTPUTDVIAnalog Audio12VIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTMONITORLINK™/HDMIVIDEO 480i/480p/720p/1080iAUDIO PCM LINEAR12IEEE 1394 INPUT/ OUTPUTNet CommandIR EMITTER .................. INPUTPC - 60HzVGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720 .......................................... .............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................. ............................................ .......... ...... Figure 9. Connecting a DVD Player with Component Video Note: NetCommand® assumes you connected your DVD player to Component-2. If you add a second DVD or use any other inputs for your DVD, this change must be reflected in the NetCommand system. See Edit NetCommand... in Chapter 3 for more information. DVI Device Figure 10 A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and audio cables are required. These are not included with the TV. They may be available at your local electronics retailer. 1. Connect the DVI-to-HDMI cable (recommended) or HDMI cable with DVI/HDMI adaptor from the DVI device’s back panel to the TV back panel. NOTE: If you are using a DVI/HDMI adaptor, it is important to connect the adaptor to the DVI device for best performance. 2. Connect a set of audio cables from AUDIO OUT on the DVI device back panel to the INPUT/DVI Analog Audio on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel. NOTE: The HDMI connection supports copy protection (HDCP). Some devices require connecting to an analog input first, in order to view on-screen menus and select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility. .................................................................................................... COMPONENTYPbPr (480i/480p/720p/1080i)INPUT12S-VIDEOVIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTDTV/CABLE/ VHF/UHFANT 1 / MAINANT 2 / AUXDIGITALAUDIOOUTPUTCableCARD™ USE WITH ANT 1 CARD TOP12YPbPrAUDIO- LEFT/ (MONO) AUDIO- RIGHTOUTPUTAUDIOOUTPUTRECORDOUTPUTDVIAnalog Audio12VIDEOAUDIO- LEFT/ (MONO) AUDIO- RIGHTMONITORLINK™/HDMIVIDEO 480i/480p/720p/1080iAUDIO PCM LINEAR12IEEE 1394 INPUT/ OUTPUTNet CommandIR EMITTER .................. INPUTPC - 60HzVGA, W-VGA, SVGA, W-SVGA, XGA, 1280 X 720 .......................................................................................... Figure 10. Connecting a DVI Device IMPORTANT...

Эта инструкция также подходит к моделям:
Телевизоры - WD-52628 (6.36 mb)
Телевизоры - WD-52628 (6.36 mb)
Телевизоры - WD-62628 (6.36 mb)
Телевизоры - WD-73727 (6.36 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории