Войти:
Оценок - 2, средний балл: 3 ( )

Инструкция по эксплуатации American Innovative,, модель 7045

Производитель: American Innovative,
Размер: 691.32 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Slide the stand off of the monitor toward you. Step 2 Attach the tilt mechanism to the adapter plate using four (4) #10-32 x 3/8” Flat Head Philips Pan screws. Step 3 Align the tilter and apple adapter bracket with the extrusion on the back of the monitor; sliding it into the slot on the bracket. Slot Slot Step 4 Attach the Apple bracket to the monitor using the (3) M3 x 16 Socket Head Screws. *You will need to press down on the bracket in order to line up the holes. (This is intended as it assures a snug fit for your monitor). Using the M3 wrench provided, tighten the M3 nuts. (Be sure the rounded part of the nut is facing upward). M3 Nuts M3x16 Screws Step 5 Use the M3 wrench to lock the (2) M3 nuts on the slide bar. Arm Assembly Page 8 Step 1 After the mount is securely fastened, insert the shaft of the arm into the mount cup. For the example the Through-Desk configuration was used. Step 2 After securing the bracket to the flat panel monitor, insert the shaft of the tilt mechanism into the forearm. Step 3 Fasten the 10-32 x 3/8" Philips Flat Head screw and washer into the hole in the bottom of the tilt mechanism to secure the monitor onto the arm. Cable Management Page 9 Step 1 * Cable clip is for Apple Monitor cable only. Other cables may be hidden within the arm as shown in Step 2. Be sure to leave enough slack for cables to loop around the elbow of the arm. Tuck the Apple monitor cord underneath the forearm, snap the cable clip into place. Step 2 The remaining cables can be hidden within the arm by following the steps and diagrams below. Feed the cables through the endcap (elbow), up through the opening in the other end of the forearm. Align the Forearm Cap over the forearm and snap into place. Align the Endcap Bumper over the bottom of the endcap and snap into place. Included with your kit is a USB extension plug. Connect the end of the USB extension into the end of the USB coming out of the keyboard. Feed the cord through the arm as above step indicates. Step 3 Tuck the monitor cable, USB extension and the remaining cables through the opening slot of the lower channel of the arm. Slide the plastic cable trough into place until it locks. Adjusting your LCD arm Page 10 Adjusting Tilt Using the 7/32” allen wrench, tilt the monitor so it faces up and locate the set screw under the tilter. To tighten friction, lightly turn the wrench to the right (clockwise). To loosen, lightly turn the wrench to the left (counter-clockwise). When your monitor moves with ease, stays tilted in the up or down position, the friction is set. *Due to the different curvature of the various monitor sizes, you may discover space between the back of your monitor and the top pads of the bracket. This space will not affect the support that your monitor receives. If you feel uncomfortable with this space, you may uninstall the bracket and bend the top two arms forward until they touch the back of your display. Adjusting Counter-balance *The monitor MUST be attached before...

Эта инструкция также подходит к моделям:
Телевизоры - 3500 (691.32 kb)
Телевизоры - 3545 (691.32 kb)
Телевизоры - 7000 (691.32 kb)
Телевизоры - 7506 (691.32 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории