Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer device will be damaged. Before you begin cloning... • The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.) • Teaching and Learning is only possible between identical model TV/STBs. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.) WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable. • Use an Installer’s remote to operate Learning and Teaching menus. • Make sure that the batteries in the Clone programmer are fresh. • If batteries are removed, the Clone Clock time will be lost. • Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a compatible TV which has had the clock set to the current time. • Setting the time and transferring it to the Clone or other device is a separate procedure. • Follow the connection diagram above to connect the Clone to a Master TV display panel. After learning is complete, to another identical TV display panel to “teach” it the master TV setup. • See the Clone Troubleshooting section to resolve problems. Turn to the next page to continue Cloning Setup. 206-4071 PAGE 31 Cloning Learning Setup Learning the Master TV Setup Instructions for the Clone Programmer to Learn the Master TV Setup Use MPI Cable to Connect LT2002 Clone Programmer to Master TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote. Learn Setup from Master TV Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master TV’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup. Set the Clock (Optional) Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.) Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability. After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.) THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX CLONE CLOCK= XX:XX TV CLOCK= XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE. This menu should appear by itself after the LT2002 is connected to the TV MPI port. CLONE SELECTION MENU (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP -TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS. -TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER This menu should appear after any key is pressed on the Installer remote. LT2002 Clone Programmer Communication Problems • A slow flashing green light indicates there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles. • If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries. PAGE 32 206-4071 Cloning Connections/Teaching Setup Teaching the Master Setup to Another TV Connections for the LT2002 to Teach another TV the Master Setup QuickSet II Programmer LT2002 ® ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA • heartbeat power on communications ok • slow power on no communications • green battery ok • red battery low Blink pattern Color Reset Status Indicator Connect cable to TV MPI Jack and follow on screen instructions MPI Ferrite Core (TDK, ZCAT 2035-0930) THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE. Antenna or CATV Target TV Clone Programmer Teach Master TV’s Setup to the target TV After learning is complete, remove the...
Эта инструкция также подходит к моделям:Телевизоры - 26-3DCH-UA (323.09 kb)