Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If OK, then possible infrared sensor trouble. (Refer to “IR Signal Check” on page 54.) • Aim the remote control directly at the infrared sensor window on the front of the unit. • Reduce the distance to the unit. • Re-insert the batteries with their polarities (+/– signs) as indicated. • When there is an infrared-equipped device such as PC near this unit, it may interrupt the remote control signal of this unit. • Move the infrared-equipped device away from this unit, change the angle of the infrared sensor or turn off the infrared communication function. How come the Initial setup appears every • Connect the RF coaxial cable to the unit directly and run the initial setup. time I turn on this unit? • Make sure to complete the channel scan before turning off the unit. Why I cannot watch some of TV programs? • Make sure autoprogram has been completed. (Refer to “Autoprogram” on page 22.) • Autoprogram must be completed when you set up the unit for the first time or move it to a location where previously unavailable channels are broadcast. • The selected channel may not be broadcasting. • When autoprogram is interrupted and not completed, some channels will not be received. Make sure to complete. (Refer to “Autoprogram” on page 22.) • The selected channel cannot be viewed by the “Child Lock” setting. (Refer to ‘‘Child Lock” on page 30.) • The unit requires some kind of antenna input. An indoor antenna (rabbit ears), an external antenna, or an RF coaxial cable from your wall or cable receiver / satellite box needs to be plugged into the unit. • Check if the right input mode is selected by pressing [SOURCE] or using How come there is no image from the [CH + / -]. (Refer to “Switching Each Input Mode” on page 19.) connected external devices? • Check the antenna or cable connection to the unit. • Many digital channels have alternate channel numbers. The unit changes Whenever I entered channel number, the numbers automatically to the ones signifying the broadcasting it changes automatically. stations. These are the numbers used for analog broadcasts. • Clean the disc. • Ensure the disc is correctly inserted. • Check if the disc is defective by trying another disc. My disc cannot be played back. • Cancel the parental lock or change the control level. Is there any way I can play my disc? • Insert a correct disc that plays back on this unit. • Handle a disc with special care so that it does not have fingerprints, scratches or dusts on its surface. • Captions that are delayed a few seconds behind the actual dialogue are Why are captions not displayed entirely? common for live broadcasts. Most captioning production companies can Or, captions are delayed behind the display a dialogue to maximum of 220 words per minute. If a dialogue dialogue. exceeds that rate, selective editing is used to insure that the captions remain up-to date with the current TV screen dialogue. How can I set the clock ? • There is no clock function on this unit. INTRODUCTION PREPARATION WATCHING OPTIONAL OPERATING DVD SETTING TROUBLESHOOTING INFORMATION EN TROUBLESHOOTING ..Troubleshooting Guide If the unit does not perform properly when operated as instructed in this manual, check the following chart and all connections once before calling for service. Symptom Remedy T V No power Make sure the AC power cord is plugged in. Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet. If a power failure occurs, unplug the AC power cord for 30 minutes to allow the unit to reset itself. • • • Control button does not work. Press only one button at a time. Do NOT press more than one buttons at the same time. • Power is ON but no screen image. Check whether the connection of the antenna, cable receiver or satellite box is connected correctly. Check whether all the cables to the unit are connected to the correct output jack of your device like BD/DVD recorder. Make sure that the selected input mode is connected to the working input jack. Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode. Tap any key on the keyboard to wake up your computer. • • • • No picture or sound Check if the power is on. Check if the right input mode is selected. Check whether all the cables to the unit are connected to the correct output jack of your device like BD/DVD recorder. View other TV channels. The problem might be limited to the broadcasting station. Turn off the unit and wait for about 1 minute, then turn on the unit again. Check whether the connection of the antenna, cable receiver or satellite box is connected correctly. Make sure that the selected input mode is connected to the working input jack. Check if your computer is NOT in sleep mode when the input mode of this unit is in PC mode. Tap any key on the keyboard to wake up your computer. Make sure that the sound is not muted. Press [MUTE] so that the volume bar and current volume level will appear on the TV screen. Make sure th...