Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
It also allows access to system-defined functionality, when available. See the description later in this chapter for more details. INFO Displays channel information. OK Press OK to select a menu item that is highlighted. CLEAR Removes any menu or display from the screen and returns you to TV viewing. ANTENNA Functions as TV/VCR button in VCR mode and TV/receiver button in SAT^CABLE mode. FORWARD Press to advance a videotape or disc. PLAY Plays a videotape or disc. PAUSE Press to pause playback. STOP Stops playing a videotape or disc. RESET Returns the picture to the original settings and displays the Picture Presets choice list. PIP, SWAP and CH CTRL do not have a function for these models 12 Graphics contained within this publication are for representation only. Chapter 2 Using the Remote Control ClonePRO™ Remote Buttons The ClonePRO can be used as a master remote. Some of the buttons only apply when using the ClonePRO to download or upload information to or from a TV. Those buttons are described in Chapter 4. RESET Returns the picture to the original settings and displays the Picture Presets choice list. Arrow buttons (up, down, left, right) Use to move through the on-screen menus. When a menu isn't displayed, the up and down arrows scan the channel list. The left and right arrows decrease or increase the TV's volume, unless Volume Hold is enabled. Go to Chapter 1 for more information on Volume Hold. MENU Displays the TV's Main menu. INFO Displays channel information. OK Press OK to select a menu item that is highlighted. CLEAR Removes any menu or display from the screen and returns you to TV viewing. Chapter 2 Graphics contained within this publication are for representation only. 13 Using the Remote Control Using the WHO*INPUT or INPUT Button Use the WHO^INPUT or INPUT button to toggle through the available input sources and view the content from the component you have connected to the TV. 1. Press TV to place the remote in TV mode. Make sure the component you want to view is turned ON. 2. Press WHO^INPUT or INPUT to tune to the available input source and view the component. 3. Press WHO^INPUT or INPUT again to tune back to the channel you were previously watching. Using the SYSTEM Button When the television is connected to an interactive system or similar device, the SYSTEM button allows you to access system programming or other special functionality through the DSCI jack (also known as "Smartplug"). On a master or basic remote, the SYSTEM button can also allow independent remote control of two TVs. Once you have specified TV1 or TV2 status for the TVs (Access & Power Options menu in Chapter 1), follow these steps to tell the remote which TV you want to operate: 1. On the remote control, simultaneously press and hold the SYSTEM button and 1 (for TV1) or 2 (for TV2). 2. After three seconds, release the buttons. The specified TV should now respond to that remote. 3. To control the other TV, simply repeat the process using the other (1 or 2) button. Programming the Remote to Operate Other Components The universal remote control can be programmed to operate most brands of remote controllable VCRs, DVD players, audio receivers, satellite receivers and cable boxes. The remote is already programmed to operate most RCA, GE and Proscan VCRs, DVD players, audio receivers and satellite receivers. Note: TheDVDbuttoncannotbepr ogrammed. Find Out If You Need to Program the Remote To determine whether the remote needs to be programmed, turn a component ON, point the remote at the component, and press the component button. Then press ON^OFF or channel up or channel down to see if the component responds to the remote commands. If not, the remote needs to be programmed. 1. Turn on the component you want the remote to operate. 2. Look up the brand and code number(s) for the component on the code list at the end of the chapter. 3. Press and hold the component button that corresponds to the component you want the remote to operate (VCR, etc.) 4. Enter the code from the code list. 5. Release the component button. 6. Press ON^OFF to see if the component responds to the remote commands. If it doesn't, try pressing the component button and then ON^OFF again. 7. If you get no response, repeat these steps using the next code listed for your brand until the component responds to the remote commands. How to Use the Remote After You've Programmed It Once the remote has been programmed successfully, you are ready to use it to control your components. To operate the component: 1. Press the component button (VCR1, VCR2, DVD, or SAT^CABLE) to set the remote to operate the component. 2. Press ON^OFF to turn the component ON or OFF. 3. Use the remote buttons that apply to that component. Note: If you keep pr essing buttonsandnothing happens, ther emoteis pr obablyin thewr ongmode. Y ou must pr essthecomponent button thatmatchesthecomponentyou wantto oper ate(i.e., ifyouwantto oper a...