Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
TV/AV : Toggle between different signal sources available 6 . MENU : To go to the On Screen Display(OSD) menus 7 . P MODE : Select different modes of picture settings 8 . S MODE : Select different modes of sound settings 9 . P+ : Scroll to next channel 10 . P- : Scroll to previous channel 11 . V- :Decrease audio volume 12 . V+ : Increase audio volume 13 . OK : Select or confirm sub menu of the OSD 14 . DISPLAY : Show info of current program 15 . SLEEP : Select time of TV to sleep mode 16 . MUTE : Mute sound 17 . .I/II: Select between mono/stereo sound or dual I/II soundtrack 18 . HOLD : Freeze screen PAGE 10 Teletext Function 1. 0-9 Channel Keys : Key in the alphanumeric digits to go to the designated page directly 2. P+ Keys : Press.P+.to scroll to the next page 3. P- Keys : Press.P-.to the previous page 4. L.ROTA Key : RED Teletext Button 5. PRE Key : GREEN Teletext Button 6. NEXT Key : YELLOW Teletext Button 7. R.ROTA Key : CYAN Teletext Button 8. TEXT Key : Switch between teletext on, mix and teletext off. 9. EAST/WEST Key : Switch between different languages 10. SUBCODE Key : Switch between secondary pages by entering the four digit number 11. INDEX Key : Go to index page directly 12. HOLD Key : Retain the current teletext page and again to cancel the function 13. SIZE Key : Switch between zooming to the upper half, lower half and in full 14. CANCEL Key : Exit from the teletext mode 15. REVEAL/CONCEAL Key : Reveal or conceal hidden text for quizzes etc PAGE 11 1. Remove the LCD TV from the box and place it on a flat surface in a well-ventilated location. 2. Connect the output terminal of RF cable to the corresponding TV RF signal input terminal. The LCD TV is a high-tech digital product. Do use quality RF cable to obtain optimal results. 3. Connect the output terminal of the AV devices such as YPbPr, DVD to the corresponding terminal of the LCD TV. 4. Connect one end of the VGA terminal to the corresponding signal source terminal, and connect the other end to the corresponding LCD TV terminal. Screw down the screws on both sides to secure it. 5. Ensure that every AV signal cord is correctly connected to the corresponding interface. 6. Connect one end of the AC power cord to the AC input jack of the LCD TV, then plug the other end to the corresponding jack. 7. The panel can be tilted upwards by no more than 100 to achieve better visual angle. When doing so, so rotate the TV with two hands, one to fix the pedestal while the other to tilt the panel. Take great care and do this in a moderate pressure in case any accidents happen. Switching the TV On 1. In Standby mode, press. .on the remote control or front panel to enter to Power On mode. 2 The indicator is red when the TV is in Standby mode. Switching the TV Off 1. Press.POWER.on the remote control or. .on the front panel to switch off the TV 2. Unplug the power cord from the AC power supply after turning off the AC power to switch the TV off completely. Caution: The TV will be shut off automatically when the power trips. Do unplug the power cord from the AC outlet if so. The last TV mode will appear when power resumes Do not turn on/off the TV too often The TV will enter into Standby mode after 15 minutes when there is no signal input in TV source; The TV will enter into sleep mode after 30 seconds when there is no stynal input in PC source. Installation General Operation PAGE 12 1. Use the On Screen Display menu to set and adjust functions 2. Use .P+./.P-. to select the desired menu after pressing.MENU., then press .V+. /.OK.to enter the next submenu; Use .V+./.V-.to adjust the options value and return to the previous menu by pressing .MENU.again. The menu will disappear without any operation within 10 seconds. Function Introduction In TV, AV, RGB, YPbPr and PC modes . Picture . Brightness To adjust the picture’s brightness . Contrast To adjust the picture’s contrast. . Sharpness To adjust the picture’s definition. . Colour To adjust the picture’s colour. . Tint To adjust the picture’s tint. (For NTSC signal only) Note: Picture menu options in other signal sources. AV/RGB: the same as in TV mode YPbPr/PC: only two options of Brightness and Contrast .Sound . Volume To increase or decrease the volume. . Balance To balance the volume between the left and right speakers. . Woofer To turn on/off the woofer. . Spatial To turn on/off the surround. . Equalizer (submenu) Use .OK. / .V+. to enter the Equalizer (submenu), you can increase or decrease the value of the sound output in every frequency band preferred Note: The Audio menu options are the same in TV signal as well as in other signal sources . Setup . Language Menu Operation PAGE 13 To select the different language displayed. . Blue Background In this mode, a blue background will appear when there is no signal input. . Program Lock In the submenu of Program Lock, the Enter Password menu appears (this menu will appear when you switch to a channel after it was locked once);. Input the default password of ...
Эта инструкция также подходит к моделям:Телевизоры - TM150F7E, TM201F7E (382.65 kb)
Телевизоры - TM150F7E, TM201F7E (382.65 kb)