Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Arlington, модель TV BRIDGE TVBR2505K

Производитель: Arlington
Размер: 136.91 kb
Название файла: ai-tvbr2505k_1.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Other patents pending. LM Arlington's new TVBR2505K TV Bridge™ includes TWO recessed power/low voltage combo boxes and all the connections you need (except for NM cable) to install a flat screen TV in an existing wall. The best part is there's no need to run cable from a panel box - or cut holes in your framing members. Just cut two holes in the wall and access power from an existing, nearby source. • Fast, easy, convenient - saves time and money! • Secure installation. Good looks. A great finish. All wires stay hidden behind the wall -no messy wires running down the wall from TV to components. Plugs stay inside the electrical box -don't protrude past the wall. • Mounting wings hold boxes securely against wall when screws are tightened. • Paintable trim plate • 18.0 cubic inch recessed boxes Arlington 1 Stauffer Industrial Park Scranton, PA 18517 800/233.4717 Fax 570/562.0646 C ©2010 Arlington Industries, Inc. Easy Installation in Existing Walls Components are not energized until the flexible cord is plugged in. Do not plug in until all other wiring is complete. 1 Locate wall studs to position TV Bridge™ between studs. 2 Position the upper box behind (or close to) the installed TV bracket. Position lower box within 3-1/2 ft. of the existing receptacle or power conditioner that will power the installation. Install upper box and lower box in the same stud cavity. 3 Pull a length of NM cable long enough to reach both boxes. Pull low voltage, coaxial, speaker wires, etc. before installing the boxes. 4 Install NM cable through the installed cable connector. Attach the boxes securely to the wall by tightening the two wing screws. 5 Wire the duplex receptacle and install it in the upper box. 6 Install LPCG50W cord grip onto the flexible cord, then install into the KD4550 using supplied locknut. 7 Connect the cord conductors to corresponding conductors of NM cable installed in the lower box. Install wire nuts. 8 Install KD4550 assembly to the lower box. Mount the CED13 cable entry device or CED1 entrance hood to the low voltage sides of both boxes (machine screws supplied). 9 Install cover plates. 10 Connect TV power cable to the installed duplex outlet in the upper box Make low voltage connections. Arlington 1 Stauffer Industrial Park Scranton, PA 18517 800/233.4717 Fax 570/562.0646 Note: - This product is not designed to be an extension of a structure's hard wiring. - Components are not energized until the flexible cord is plugged in. Do not plug in until all other wiring is complete. Patents pending TVBR2505K 0410/15M CATALOG UPC/DCI/NAED DESCRIPTION UNIT/STD NUMBER MFG #01 8997 PKG TVBR2505K 09658 TV Bridge™ 1 TVBR2505KGC 09108 TV Bridge™ 1 with ground clip (for Canada) Includes (2) recessed boxes with trim plates and installed NM cable connectors, (2) duplex covers, wire nuts, tamper-resistant duplex receptacle, installation screws, LPCG50W cord grip, 4 ft. cord, KD4550 and The SCOOP™ (2) CED1 entrance hoods, (2) CED13 cable entry devices. Distributed by...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории