Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not press any keys on the TV, remote control, or Cable box until the testing process is completed. When testing is completed, screen 11 appears. Screen 11: If your Cable box tuned itself to channel 09 after testing, select YES and press ENTER. If you selected ANT 1 in screen 5, screen 13 appears. If you selected VIDEO 1 in screen 5, screen 12 appears. If your Cable box did not tune itself to channel 09 after testing and you want to test the same code again, select TEST THIS CODE AGAIN and press ENTER. If you want to test a different code, select NO and press ENTER. Screen 10 appears. Note: Many cable boxes require testing more than one code. (Continued on next page) Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 37 51,57HX94(E)036-39 37 9/12/04, 7:07 PM Chapter 5: TV Guide On Screen setup Setting up the TV Guide On Screen system (continued) Screen 12: Do you have an antenna connected? Select either YES or NO, and then press ENTER. Screen 13 appears. Note: If you selected NO in screen 3, you must select YES in this screen to receive a channel lineup and program listings. Screen 14: Congratulations! You have completed basic TV Guide On Screen system setup. Note: Read the on-screen information regarding the amount of time it may take for listing information to download from the TV Guide On Screen service. Press ENTER to display screen 15. Screen 13: Are the settings correct? If you select YES, screen 14 appears. If you select NO, screen 1 appears. Screen 15: Is a VCR connected? If you select YES, screen 16 appears. If you select NO, screen 21 appears. Screen 16: The on-screen diagram shows the correct way to connect your VCR to the G-LINK™ jack on the TV. Make sure the G-LINK cable is installed properly. For additional details, see page 25. Press ENTER to display screen 17. Screen 17: Select your VCR brand, and then press ENTER. Screen 18 appears. Screen 18: Turn on your VCR, insert a tape (either blank or previously recorded), and then press PLAY. Screen 19 appears. Screen 19: The TV Guide On Screen system will test the code for the brand of VCR you selected. Do not press any keys on the TV, remote control, or VCR until the testing process is completed. When testing is completed, screen 20 appears. 38 38 Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 51,57HX94(E)036-39 38 9/12/04, 7:07 PM Chapter 5: TV Guide On Screen setup Setting up the TV Guide On Screen system (continued) Screen 20: If your VCR stopped playing the tape after testing, select YES and press ENTER. Screen 21 appears. Did your VCR stop playing? If your VCR did not stop playing the tape after testing and you want to test the same code again, select TEST THIS CODE AGAIN and press ENTER. If you want to test a different code, select NO and press ENTER. Screen 19 appears. Note: Many VCRs require testing more than one code. Screen 21: Review the setup information displayed on your TV screen (an example is shown below). If the information on your TV screen is correct for your setup, select YES, END SETUP and press ENTER. Screen 22 appears. If the information is incorrect, select NO, REPEAT SETUP PROCESS and press ENTER. Screen 1 appears. Screen 22: Congratulations! You have successfully completed TV Guide On Screen system setup. Press ENTER to display screen 23. Screen 23: This screen provides helpful information on using your TV Guide On Screen system. Press ENTER to exit the TV Guide On Screen setup and watch TV. TV Guide On Screen Reminder The TV Guide On Screen system receives program listings data through your Cable or over-the-air video signal. In order to receive regular program listings, please remember to do the following: 1. Leave the TV in standby mode when it is not in use (such as overnight or when you are not watching it) by turning it OFF but leaving the power cord plugged in. 2. If you have a Cable box connected, leave it ON. 3. If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.) See page 13 for VCR connection instructions. 4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, follow the on-screen instructions. Copyright © 2004 TOSHIBA CORPORATION. All rights reserved. 39 51,57HX94(E)036-39 39 9/12/04, 7:07 PM 6 Setting up your TV For menu navigation instructions, see Chapter 4. Selecting the menu language You can choose from three different languages (English, French and Spanish) for the on-screen display of adjustment menus and messages. (The TV Guide On Screen menus are in English, regardless of the language selected in this menu.) To select the menu language: 1. Press MENU and open the PREFERENCES menu. 2. Highlight MENU LANGUAGE and press ENTER. 3. Highlight your preferred menu language in the menu sidebar and press ENTER. 4. Press EXIT to close the PREFERENCES menu. Configuring the antenna input sources To configure the ANT 1 and ANT 2 input sources: 1. Press MENU and ope...