Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Connect both antenna leads to the combiner. Plug the combiner into the “ANT 1 IN” terminal on the rear panel. Connecting VHF and UHF Antennas If you do not have a cable system, you will need to connect an antenna to your TV. Antennas with 300-ohm Flat Twin Leads If your antenna looks like this: it has 300-ohm flat twin leads. Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws. Plug the adapter into the “ANT 1 IN” terminal on the rear panel. Quick Guide Connections Connecting Cable TV and VCR You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable box that descrambles some or all channels. Connecting a Cable Converter Box This connection allows you to watch cable and premium channels. You should keep your TV selected to “ANT 1 IN” so that you can use the TV features. When viewing premium channels, select “ANT 2 IN” and tune the TV to channel 3 or 4 (whichever channel is vacant in your area), then use the converter box to change channels. You will need two coaxial cables. NOTES • When you use a converter box with your TV, there may be features that you can not program using the remote control, such as programming your favorite channels and blocking channels. • The output from “ANT 1 OUT” is available when select “Ant.2” in the “Antenna“ channel menu. Connecting a Camcorder The side panel jacks on your TV make it easy to connect a camcorder to your TV. You can use your camcorder to view tapes without using a VCR. From Cable TV Rear Panel Connecting a Cable Converter Box and a VCR This connection allows you to watch and record basic and premium cable channels, as well as watch videotapes. You should keep your TV selected to “ANT 1 IN” so that you can use the TV’s features. When viewing premium channels or recording with the VCR, select “ANT 2 IN” (whichever channel is vacant in your area), then use the converter box to change channels. Caution: If you want to record one channel while watching another channel, a splitter (not included) must be added between the cable and “ANT 1 IN”. One output of the splitter goes to “ANT 1 OUT” and the second output is connected to IN on the cable converter box. If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable. If you have a S-VHS VCR, use the S-video connections and remove the video cable. Do not connect the video cable and the S-video cable to video1 simultaneously. When you use a converter box with your TV there may be features that you can not program using the remote control, such as programming your favorite channels and blocking channels. Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the camcorder. If you have mono camcorder, connect L(mono) to camcorder audio out using only one audio cable. Connect a video cable between the VIDEO IN (or S-VIDEO IN) jack on the TV and the VIDEO OUT jack on the camcorder. The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. From Cable Camcorder TV Side Panel Camcorder Output Jacks TV Rear Panel VCR Connecting to Y, PB, PR Connect a set of audio cables between the COMPONENT (1 or 2) audio (L, R) in jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. Connect a set of video cables between the COMPONENT (1 or 2) VIDEO (Y, PB, PR) in jacks on the TV and VIDEO (Y/PB/PR or Y/CB/CR) OUT jacks on the Set-Top Box. NOTE : For an explanation of Component video, see your Set Top Box owner's manual. Connecting to DVI (Digital Visual Interface) Connect a set of audio cables between the DVI audio (L, R) in jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. Connect a video cable between the DVI IN jack on the TV and the DVI OUT jack on the Set-Top Box. Connecting a DTV Set-Top Box Incoming Cable or Antenna TV Rear Panel DTV Set-Top Box TV Rear Panel DTV Set-Top Box Incoming Cable or Antenna Connecting to R,G,B Connect a set of audio cables between the PC audio (L, R) in jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. Connect a video cable between the PC IN jack on the TV and the R.G.B OUT jack on the Set-Top Box. Connecting to HDMI (High Definition Multimedia Interface) Connect a HDMI cable between the HDMI IN jack on the TV and the HDMI OUT jack on the Set-Top Box. NOTE : Please check if the power of HDMI source is on, in case that you fail to select HDMI from the “Source List” even after you connected the cable of HDMI source (DTV Set-Top Box, DVD, etc.) to TV. Incoming Cable or Antenna DTV Set-Top Box TV Rear Panel TV Rear Panel DTV Set-Top Box Incoming Cable or Antenna Antennas with 75-ohm Round Leads If your antenna looks like this: it is an antenna with 75-ohm roun...