Up to 8 programs can be placed in memory. You can choose to record one time, daily, or weekly. kX Check fist before you begin. □ All connections are made (see page 5). □ Your Combination VCR is plugged in. □ The clock is set. □ The tape is long enough. □ The record tab is in place. PROGRAM TIMER Indicator (3) Push PROG to display the “SET PROGRAM” screen. Push A W to select “TIMER PROGRAM,” and then push E>to display the program screen. •If a program is already in memory, push A ▼ repeatedly, and then [> to select an unused program number. --- SET PROGRAM --VCR P KEY END :PROG KEY Push A Tand [>to select and set one of the following: 1-31 = One time recording DAILY = Same time MON - FRI WEEKLY = Same time once a week Example ^8—9........31—1—2...... Today’s_7 SELECTA/T Selection Order DAILY (Date I WEEKLY WEEKLY_WEEKLY _J ^ (SAT) ...... (MON) (SUN) Push A Vand O [>to select and set each of the remaining items at right. Remaining Items: • START time • STOP time • CH(annel) number, or LINE for outside source recording • Speed (SP, LP, SLP) To Make Corrections Repeatedly push [> to move the cursor to the right, or<]to move to the left to the incorrect entry and make the correction. Push PROG to end the program. • This screen appears for confirmation. To Enter More Programs Push m V and Oto select and set a blank program number, and then repeat steps 3 and 4. P DT START STOP CH SPD 11.1; 2---- 3---- __ — CANCEL SELECT ENTER END ADD/DI 1-8 : * ► KEY PROG .T KEY ▼ KEY EY Push PROG twice to return to the normal screen. • The PROGRAM TIMER indicator lights on the front panel. • If you’re using a cable box, make sure that it is tuned to the desired channel and the power is left on for timer recording. Two minutes before the Timer Recording starts, “TIMER REC WILL START SOON” will appear on-screen. 20 Cancel a Timer Recording: (Recording js in progress) Hold down STOP for a few seconds to cancel the Timer Recording. • Any future daily or weekly recordings will be performed as programmed. TIMER Indicator Replace Program Contents: (Recording is not in progress) 1 Do steps 1 and 2 on previous page. All currently set programs will be displayed on-screen. 2 Push A Vrepeatedly to select the desired timer recording, and then push [♦Mo display the settings. (See page 20.) 3 Push A ^repeatedly to select, and then push £► to enter replacement information. 4 Push PROG three times to exit this mode and return to the normal TV screen. P DT START STOP o X SPn 0---- — -- 2 8 10 OOp 12: OOp 125 SLP 3 10 0 00 p 9:00 p 10 SP 4 SU 9 OOp 10 : OOp L SLP SELECT 1-0 : A T KEY ENTER ► KEY END PROG KEY rçfJ'Eiy START STOP CH / |V/| \ SLP SELECT START DATE SELECT :a t KEY SET :■* ► KEY END : PROG KEY Review or Clear Program Contents: (Recording is not in progress) а. Do steps 1 and 2 on previous page. All currently set programs will be displayed on-screen. б. Push A Trepeatedly to select the desired program number. c. Push the ADD/DLT to clear the program. tf. Push PROG twice to exit this mode and return to the normal TV screen. P DT START STOP n CH SPD 2 8 10:OOp 12:OOp 125 SLP 3 10 8:OOp 9:OOp 10 SP 4 SU 9:00pI0:00p L SLP SELECT 1-8:A ▼ KEY ENTER :► KEY END : PROG KEY P DT START STOP CH SPD 2 8 10 : OOp 12 :00p 125 SLP 3 10 8 :OOp 9 :OOp 10 SP 4 SU 9:OOp 10:OOp L SLP CANCEL:ADD/DLT KEY SELECT 1-8:A T KEY ENTER :► KEY END : PROG KEY If “PLEASE PREPARE FOR TIMER REC” appears and/or the PROGRAM TIMER indicator flashes, check that a cassette with record tab is loaded and the Combination VCR is in Stop mode. If the start times of two programs overlap, the lower numbered program will have priority. If the start time for a timer recording comes up during a normal recording or One Touch Recording (page 18), the timer recording will not be performed. If there is a power interruption of more than one minute, the recording may not be performed or continue. If “INCOMPLETE” appears after all items have been set, check all entries and make necessary corrections. 21 More you Can Do MTS Broadcast/TV Stereo System k/ Check list before you begin. □ All connections are made (see page 5). □ Your Combination VCR is plugged in. IMPORTANT NOTE: This stereo system is designed for TV viewing only. Recording and playback will always be in monaural. Receivable Broadcast Types The following are possible broadcast types with their accompanying on-screen displays. The signal being received is indicated with an “((<” mark while the selected audio mode is indicated with an arrow. To change the audio mode for these broadcasts, follow the “Select Audio Mode for TV Viewing” section, (below) DISPLAY o Push DISPLAY to display the broadcast signal currently being received. MTS Stereo and SAP broadcast Multi-chann...
)
