Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Using a stud finder, locate and mark the stud for securing the mount (make sure your mark is in the center of the stud). You can use your own stud finder or the one included in the hardware kit. D Note Once stud has been located you will need to verify with a hammer and a nail A) Simply place the nail over your mark on the wall and tap in with hammer. If the nail encounters resistance and is secure in wall you have verified a stud location B) If it just pushes through with no resistance you will need to start over and locate the stud. 3 Using the enclosed mounting template, place the diagram against the wall and mark two locations (top and bottom) on the wall where the mount is to be Installed. Be sure to use the center of the stud. 4 5 6 7 8 With the help of another person, place the mount against the wall and level it using the bubble guide. While another person holds the mount in place, mark two locations (top and bottom) on the wall where the mount is to be installed. Be sure to use the center of the stud. (these marks should line up with the ones made in step 3 above using the template). Set the mount aside and drill a 1/8” (3 mm) pilot hole at each marked location. Place the mount back against the wall and secure it using the wood screws (A) provided. Do not over-tighten these screws and do not release the mount until all screws are in place. Once both wood screws are in place you must tighten each one. (note: be sure not to over tighten). 1 Wall Piece 1 3.2 Mounting the wall plate (concrete/brick installation) B Warning For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and display. 1 See enclosed mounting template for diagram and guide of how to mount properly on the wall. 2 3 4 5 6 Using the enclosed mounting template, place the diagram against the wall and mark four locations on the wall where the mount Is to be Installed. With the help of another person, place the mount against the wall and level it using the bubble guide. While another person holds the mount in place, mark four locations on the wall where the mount is to be installed. Set the mount aside and drill a 5/16” (8mm) pilot hole at each marked location. Remove any excess dust from the holes. Insert a Concrete Anchor (B) into each hole so that it is flush with the concrete surface.A hammer can be used to lightly tap the anchors into place if necessary. 2 2 1 2 7 Place the mount back against the wall and secure it using the wood screws (A) provided. Do not over-tighten these screws and do not release the mount until all screws are in place. D Note If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface. 8 Once all four wood screws are in place you must tighten each one. Be sure not to over tighten. 3 Wall Piece 3 3.3 Attaching the mount to the display B Warning Make sure the LCD is unplugged before starting this step of the installation and never lay the LCD face down as this may damage the viewing surface. Before attaching the mount to your LCD, you must first determine which hardware to use. Do this by examining the back of the LCD. If your LCD has a flat back, use one of the short bolts (C or D). If your LCD has a recessed back, use the longer M4x30mm bolts (E) or M6x35mm bolts (G) and 3/4” spacers (F) or (H) large spacers (H). After you have determined the appropriate bolts, use them to attach the mount to the back of your LCD. 4 Display Spacer(F or H) Only if using C orG Spacer (F or H) Only if using E or G Bolt (C, D, E, or G) 4 ETip Be careful not to over-tighten the bolts. D Note For safety reasons it is required that all 4 bolts are used when mounting your TV. 4 Final installation and operation 4.1 Final installation 1 2 To complete the installation, simply slide the mount with your LCD attached into the wall piece. For additional security and stability, insert the M4x12 bolts into the holes located on the base of the unit and tighten with a screwdriver. 5 Display M4 x 12 Bolt (C) Installed Wall Piece Display 5 B Warning Insert the M4x12 bolts at the bottom of the mount to avoid having the display accidentally knocked off the mount. 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount. Call 1-919-573-7854. Limited Two-Year Warranty Philips warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specications and warnings, for two years from the date of your purchase of this product.This warranty extends only to the original purchaser of the product, and is not transferable.To exercise your rights under this warranty, you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase. For customer support or to obtain warranty service, please call 919-573-7854.THE...
Эта инструкция также подходит к моделям:Телевизоры - SQM4122 (1.02 mb)