Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. LEGEND WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to this mount does not exceed 200 lbs (91 kg). WARNING: The installer is responsible for verifying that the 1 1/2” NPT fixture this mount is installed on is capable of supporting four times the maximum weight capacity of the mount as stated above. Tighten Fastener Apretar elemento de fijacion Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Сожмите Застежку Loosen Fastener Aflojar elemento de fijacion Befestigungsteil losen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Ослабьте Застежку Open-Ended Wrench Llave de boca Gabelschlussel Chave de bocas Chiave a punte aperte Steeksleutel Cle a fourche Открытый Рывок Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Приспособьтесь Hex-Head Wrench Llave de cabeza hexagonal Sechskantschlussel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cle a tete hexagonale Главный ведьмой Рывок Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Отвертка Installation Instructions PCM SERIES 3 TOOLS REQUIRED FOR INSTALLATION AND PARTS DIMENSIONS Figure 1 x1 I/M B (1) 3/16" (provided) C (1) D (6) A (1) PCM SERIES Installation Instructions 4 Mount Assembly and Installation 1. Fold tube out until tube mounting bracket rests against faceplate mounting bracket. (See Figure 2) 2. Secure tube to faceplate mounting bracket using 3/16" hex wrench (C) and two 5/16-18 x 1/2" button head cap screws (D). 3. Tighten all hardware. Figure 2 4. Thread the tube assembly (A) onto 1-1/2” NPT. NOTE: The product is suitable for use with a Listed ceiling plate which can accommodate 1-1/2" NPT pipe, and has a rated weight capacity of 200 lbs (91 kg). 5. Secure faceplate (B) to faceplate mounting bracket using 3/16" hex wrench (C) and four 5/16-18 x 1/2" button head cap screws (D). Figure 3 Display Installation If the mounting pattern of the display being installed is a VESA standard 200 x 200 pattern the mounting buttons can be installed directly to the back of the display. If the display has any other mounting pattern an interface bracket must be obtained before proceeding. Consult a Chief Customer Service representative if an interface bracket is required by calling 1-800-582-6480 or visit WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Displays can weigh in excess of 40 lbs (18.1kg). ALWAYS use two people and proper lifting techniques when installing display. WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make sure mounting buttons on display are properly seated in mounting holes in faceplate. To install display: 1. While supporting both sides of display, align four mounting buttons on display or interface bracket with four mounting holes in faceplate. (See Figure 4) 2. Lower display into place listening for audible "click" to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and "click lock" mechanism has engaged. (See Figure 4) and (See Figure 5) Figure 4 NOTE: Holes are provided in the faceplate for use with a padlock or similar locking device, if desired. In addition, the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device. (See Figure 5) 1 2 (D) x 2 5 (A) x1 (D) x4 (B) x 1 2 1 I...