Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
2 Internal EDID LED This LED will activate only when the pre-programmed internal EDID is being used. Please see page 6 for more details on the internal EDID. 3 External EDID LED (default EDID routing) This LED will activate only when the external EDID is being used. Please see page 6 for more details on the external EDID. 4 Link LED This LED will activate when a valid link between the source and the splitter is detected. 5 EDID Button This button will activate the onboard EDID. Press this button (the Int. EDID should turn on and the Ext. LED should turn off) and reset the unit using the Reset button (below) to initialize this EDID mode. To use an external EDID, press the EDID button again (the Int. LED should turn off and the Ext. LED should turn on) and press the Reset button to initialize this EDID mode. 6 Reset Button This button will reset the unit and initialize whichever EDID mode is currently selected. 4 PANEL DESCRIPTIONS 7 HDMI Input This is the input for the HDMI source device. When a valid source is detected by the splitter, the Link LED will activate. 8 HDMI Out 1 This is the first HDMI output port. Connect a valid HDMI display to this port. When the External EDID mode is active, the EDID form the display connected to this port will be used to send to the source. 9 HDMI Out 2 This is the second HDMI output port. Connect a valid HDMI display to this port. 10 5V DC Power Input This port is for the included 5V DC power supply. When a valid 5V power supply is attached, the Power LED will activate. 5 CONNECTING AND OPERATING THE 1:2 SPLITTER FOR HDMI How to Connect the 1:2 Splitter For HDMI 1.3 1. Connect the supplied cable from the HDMI source into the 1:2 Splitter for HDMI 1.3 input. 2. Connect the cables from your displays (monitor or projector) into the HDMI outs of the 1:2 Splitter for HDMI 1.3. Up to 2 displays are supported. 3. Plug the 5V DC power supply into the 1:2 Splitter for HDMI 1.3. NOTE: By Default, the display information from the display connected to HDMI output port 1 is sent back to the source. Therefore, the other display that is connected to the 1:2 Splitter for HDMI 1.3 must be capable of accepting the timings and resolutions of the display that is connected to HDMI output port 1. It is recommended that the display with the lowest native resolution be connected to HDMI output port 1. This is to ensure that a compatible video signal will be able to be displayed on all connected monitors. There is a generic EDID programmed into the 1:2 Splitter for HDMI 1.3 that can be used instead. Please see below for the activation process. EDID MODE The HDMI 1:2 has an EDID button which will determine if the EDID is used from the display attached to output 1 (Ext. mode) or if the onboard EDID (Int. mode) will be used. The current EDID mode can be determined by which EDID mode LED is active on the front panel. The Ext LED will indicate that the external EDID (from output port 1) is being used, and the Int LED will indicate that the internal pre-programmed EDID is being used. If you want to use the onboard EDID, press the EDID button on the rear panel and then press the reset button to activate the new EDID mode. To revert back to using the external EDID, press the EDID button again and then reset the unit using the reset button to activate the new EDID mode. Listed Resolutions in the Internal EDID: 1280x720p 50 Hz (Naitive) 1280x720p 59.94 / 60 Hz (Naitive) 1920 x 1080i 50 Hz 1920 x 1080i 59.94 / 60 Hz 720 x 480p 59.94 / 60 Hz 720 x 576p 50 Hz 1920 x 1080p 50 Hz 1920 x 1080p 59.94 / 60 Hz 1440 x 480p 59.94 / 60 Hz 1440 x 576p 50 Hz 6 SPECIFICATIONS Video Amplifier Bandwidth ............................................................... 225 MHz Input Video Signal ...................................................................... 1.2 Volts p-p Input DDC Signal ................................................................ 5 Volts p-p (TTL) Single Link Range ........................................................... 1080p/1920 x 1200 HDMI Connector ......................................................... Type A 19 Pin Female Power Supply ...................................................................................... 5V DC Power Consumption .............................................................. 13 Watts (max) Dimensions .................................................................... 9.4”W x 1”H x 4.6”D Shipping Weight .................................................................................... 3 lbs. 7 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notified within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Equipment that fails under conditions other than those covered will be repai...